ADT7463 Analog Devices, ADT7463 Datasheet - Page 13
ADT7463
Manufacturer Part Number
ADT7463
Description
Dbcool Thermal Management Controller And Voltage Monitor
Manufacturer
Analog Devices
Datasheet
1.ADT7463.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADT7463A
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADT7463ARQ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADT7463ARQ-REEL
Manufacturer:
MURATA
Quantity:
16 000
Part Number:
ADT7463ARQ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADT7463ARQZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADT7463ARQZ-REEL
Manufacturer:
ONSEMI
Quantity:
2 785
Part Number:
ADT7463ARQZ-REEL
Manufacturer:
ON/安森美
Quantity:
20 000
STEP 7: DETERMINING T
CHANNEL
T
the temperature measured has dropped back below T
before the fan turns off. The premise for temperature
hysteresis (T
“chatter,” or cycle on and off regularly, whenever tem-
perature is hovering at about the T
The T
time needed for the system to cool down or heat up as
the fan is turning on and off. Values of hysteresis are
programmable in the range 1°C to 15°C. Larger values of
T
viously described. The T
REV. 0
HYST
HYST
is the amount of extra cooling a fan provides after
prevent the fans from chattering on and off as pre-
HYST
value chosen will determine the amount of
HYST
AMBIENT TEMP
REMOTE 2 =
REMOTE 1 =
VRM TEMP
) is that without it, the fan would merely
CPU TEMP
100%
LOCAL =
0%
Figure 17. The T
T
HYST
HYST
HYST
T
MIN
T
T
FOR EACH TEMPERATURE
T
MIN
MIN
THERMAL CALIBRATION
THERMAL CALIBRATION
THERMAL CALIBRATION
default value is set at 4°C.
MIN
MIN
HYST
T
RANGE
setting.
T
T
T
RANGE
RANGE
RANGE
Value Applies to Fan On/Off Hysteresis and THERM Hysteresis
T
THERM
100%
100%
0%
100%
0%
0%
MUX
MIN
–13–
PWM
PWM
PWM
MIN
MIN
MIN
Note that the T
temperature hysteresis for fan turn on/off, but the same
setting is used for the T
in Step 6. So programming registers 0x6D and 0x6E sets
the hysteresis for both fan on/off and the THERM function.
HYSTERESIS REGISTERS
Reg. 0x6D Remote 1, Local Hysteresis Register
<7:4> = Remote 1 Temp Hysteresis (4°C default)
<3:0> = Local Temp Hysteresis (4°C default)
Reg. 0x6E Remote 2 Temp Hysteresis Register
<7:4> = Remote 2 Temp Hysteresis (4°C default)
Note that in some applications, it is required that the
fans not turn off below T
PWM
(Reg. 0x62) allow the fans to be turned off, or to be kept
spinning below T
value has no effect on the fan when the temperature drops
below T
ENHANCEMENT)
TACHOMETER 1
MEASUREMENT
ENHANCEMENT)
TACHOMETER 2
MEASUREMENT
ENHANCEMENT)
TACHOMETER 3
MEASUREMENT
(ACOUSTIC
(ACOUSTIC
(ACOUSTIC
CONTROL
CONTROL
CONTROL
MIN
AND 4
RAMP
RAMP
RAMP
MIN
. Bits <7:5> of Enhance Acoustics Register 1
.
GENERATOR
GENERATOR
GENERATOR
CONFIG
CONFIG
CONFIG
PWM
PWM
PWM
PWM
PWM
PWM
HYST
MIN
. If the fans are always on, the T
setting applies not only to the
THERM
PWM1
TACH1
PWM2
TACH2
PWM3
TACH3
MIN
hysteresis value described
but remain running at
AN-613
CPU
FAN SINK
FRONT
CHASSIS
REAR
CHASSIS
HYST