LT6004 Linear Technology Corporation, LT6004 Datasheet - Page 7

• Manufacturer Part Number: LT6004
• Description: 1.6v, 1?a Precision Rail-to-rail Input And Output Op Amp
• Manufacturer: Linear Technology Corporation

electrical characteristics
apply over the full specified temperature range of –40°C ≤ T
otherwise noted.
SYMBOL
V
ΔV
I
I
CMRR
PSRR
V
V
I
I
SR
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: A heat sink may be required to keep the junction temperature
below absolute maximum. This depends on the power supply voltage and
how many amplifiers are shorted. The θ
DHC packages is with minimal PCB heat spreading metal. Using expanded
metal area on all layers of a board reduces this value.
Note 3: The LT6003C/LT6004C/LT6005C and LT6003I/LT6004I/LT6005I are
guaranteed functional over the temperature range of –40°C to 85°C. The
LT6003H/LT6004H/LT6005H are guaranteed functional over the operating
temperature range of –40°C to 125°C.
Note 4: The LT6003C/LT6004C/LT6005C are guaranteed to meet specified
performance from 0°C to 70°C. The LT6003C/LT6004C/LT6005C are
designed, characterized and expected to meet specified performance from
B
OS
SC
S
OS
OL
OH
OS
/ΔT
PARAMETER
Input Offset Voltage
Input Offset Voltage Drift (Note 5)
Input Bias Current
Input Offset Current
Common Mode Rejection Ratio
Input Offset Voltage Shift
Input Voltage Range
Power Supply Rejection Ratio
Output Swing Low (Notes 6, 8)
Output Swing High (Note 6)
Short Circuit Current
Supply Current per Amplifier
Slew Rate (Note 11)
JA
specfied for the DC, DD and
CONDITIONS
LT6003S5, LT6004MS8
LT6005GN
LT6004DD, LT6005DHC
LT6003DC
S5, MS8, GN
DC, DD, DHC
LT6003
LT6004, LT6005
LT6003
LT6004, LT6005
V
V
V
V
V
V
Guaranteed by CMRR
V
No Load
I
No Load
I
Short to GND
A
SINk
SOURCE
V
CM
CM
CM
CM
CM
CM
S
= ±1.1V to ±8V
= –1, R
= –7.7V to 6.9V
= –7.7V to 7.7V, S5, MS8, GN
= –7.7V to 7.7V, DC, DD, DHC
= –7.7V to 6.9V
= –7.7V to 7.7V, S5, MS8, GN
= –7.7V to 7.7V, DC, DD, DHC
= 100µA
= 100µA
F
= R
(LT6003H, LT6004H, LT6005H) The
A
G
≤ 125°C. V
= 1MΩ
–40°C to 85°C but are not tested or QA sampled at these temperatures.
The LT6003I/LT6004I/LT6005I are guaranteed to meet specified
performance from –40°C to 85°C. The LT6003H/LT6004H/LT6005H are
guaranteed to meet specified performance from –40°C to 125°C.
Note 5: This parameter is not 100% tested.
Note 6: Output voltage swings are measured between the output and
power supply rails.
Note 7: Limits are guaranteed by correlation to V
Note 8: Limits are guaranteed by correlation to V
Note 9: Limits are guaranteed by correlation to V
Note 10: Full-power bandwidth is calculated from the slew rate:
Note 11: Slew rate measured at V
guarantee by correlation the slew rate at V
slew rate at V
S
FPBW = SR/πV
= ±8V, V
S
CM
= ±8V, V
LT6003/LT6004/LT6005
= V
P-P
.
OUT
OUT
= half supply, R
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
= –5V to 5V.
●
denotes the specifications which
S
–7.7
MIN
0.2
90
78
76
84
= 1.8V, V
1
S
= 5V, V
L
OUT
to ground, unless
TYP
2
3
= 0.4V to 1.4V is used to
S
S
S
= 5V tests.
= 1.8V tests
= ±8V tests
OUT
= 1V to 4V and the
MAX
460
275
140
400
1.6
1.8
2.2
1.9
2.5
7.7
12
60
2
6
8
6
2
4
3
600345fb
UNITS
µV/°C
µV/°C
V/ms

mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mA
µV
µA
nA
nA
nA
nA
dB
dB
dB
dB
V