CC2420 Chipcon AS, CC2420 Datasheet - Page 73
CC2420
Manufacturer Part Number
CC2420
Description
2.4 GHz RF Transceiver for IEEE 802.15.4 and ZigBee
Manufacturer
Chipcon AS
Datasheet
1.CC2420.pdf
(85 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CC2420-RTR1
Manufacturer:
COOPER/Bussmann
Quantity:
25 000
Company:
Part Number:
CC2420RGZR
Manufacturer:
TI/CC
Quantity:
9 035
Part Number:
CC2420RGZR
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
CC2420RGZT
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
CC2420RTCR
Manufacturer:
TI/CC
Quantity:
18 300
Part Number:
CC2420RTCR
Manufacturer:
TI-CHIPCON
Quantity:
20 000
Company:
Part Number:
CC2420ZRTCR
Manufacturer:
TI-CHIPCON
Quantity:
12 300
MANOR (0x22) - Manual signal OR override register
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
AGCCTRL (0x23) - AGC Control
15:12
11
10:4
3:2
1:0
Chipcon AS SmartRF ® CC2420 Preliminary Datasheet (rev 1.0), 2003-11-17
Bit
Bit
Field Name
VGA_RESET_N
BIAS_PD
BALUN_CTRL
RXTX
PRE_PD
PA_N_PD
PA_P_PD
DAC_LPF_PD
XOSC16M_PD
RXBPF_CAL_PD
CHP_PD
FS_PD
ADC_PD
VGA_PD
RXBPF_PD
LNAMIX_PD
Field Name
-
VGA_GAIN_OE
VGA_GAIN [6:0]
LNAMIX_GAINMODE_O
[1:0]
LNAMIX_GAINMODE
[1:0]
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Reset
0
0
0x7F
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
W0
R/W
R/W
R/W
R
SmartRF
Description
The VGA_RESET_N signal is used to reset the peak detectors in
the VGA in the RX chain.
Global Bias power down (1)
The BALUN_CTRL signal controls whether the PA should receive
its required external biasing (1) or not (0) by controlling the
RX/TX output switch.
RXTX signal: controls whether the LO buffers (0) or PA buffers
(1) should be used.
Powerdown of prescaler.
Powerdown of PA (negative path).
Powerdown of PA (positive path). When PA_N_PD =1 and
PA_P_PD=1 the up-conversion mixers are in powerdown.
Powerdown of TX DACs.
Powerdown control of complex bandpass receive filter calibration
oscillator.
Powerdown control of charge pump.
Powerdown control of VCO, I/Q generator, LO buffers.
Powerdown control of the ADCs.
Powerdown control of the VGA.
Powerdown control of complex bandpass receive filter.
Powerdown control of LNA, down-conversion mixers and
frontend bias.
Description
Reserved, write as 0
Use the VGA_GAIN value during RX instead of the AGC value.
When written, VGA manual gain override value; when read, the
currently used VGA gain setting.
LNA / Mixer Gain mode override setting
0 : Gain mode is set by AGC algorithm
1 : Gain mode is always low-gain
2 : Gain mode is always med-gain
3 : Gain mode is always high-gain
Status bit, defining the currently selected gainmode selected by
the AGC or overridden by the LNAMIX_GAINMODE_O setting.
®
CC2420
Page 73 of 85