MAX4559 Maxim, MAX4559 Datasheet
MAX4559
Available stocks
Related parts for MAX4559
MAX4559 Summary of contents
Page 1
... Rev 0; 4/99 ±15kV ESD-Protected, Low-Voltage, CMOS General Description The MAX4558/MAX4559/MAX4560 are low-voltage, CMOS analog ICs configured as an 8-to-1 multiplexer (MAX4558), a dual 4-to-1 multiplexer (MAX4559), and a triple single-pole/double-throw (SPDT) switch (MAX4560). Each switch is protected against ±15kV electrostatic discharge (ESD) shocks, without latchup or damage. These CMOS devices can operate continuously from dual supplies of ± ...
Page 2
... 4.5V, -4.5V MAX4559 -4.5V, 4. MAX4560 MAX4558 , V = 5.5V -5.5V 4.5V, 4.5V MAX4559 4.5V, -4. MAX4560 = +70° unless otherwise noted. Typical values MAX MIN TYP MAX T UNITS A (Note +25°C 110 160 C, E 180 +25°C ...
Page 3
... Figure 5 MAX4558 ), GND 1MHz MAX4559 Figure 5 MAX4560 MAX4558 GND MAX4559 f = 1MHz; Figure 5 MAX4560 unless otherwise noted. Typical values MIN MAX MIN TYP MAX T A (Note 2 0 ±2 ±6 +25° ...
Page 4
... 1V, 4.5V MAX4559 4.5V MAX4560 MAX4558 , V = 5.5V 1V, 4.5V MAX4559 1V, 4. MAX4560 unless otherwise noted. Typical values MAX MIN TYP MAX T UNITS A (Note 2) +25°C -96 +25°C - 180 +25°C 0.02 +25°C 110 +85°C 70 +25° ...
Page 5
ESD-Protected, Low-Voltage, CMOS ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued +4.5V to +5.5V +25°C.) A PARAMETER SYMBOL DIGITAL I Input Logic High ...
Page 6
... ON(MAX) ON(MIN) Note 4: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal ranges; i.e., V Note 5: Leakage parameters are 100% tested at the maximum-rated hot operating temperature and are guaranteed by correlation +25°C. A Note 6: Guaranteed by design, not production tested. ...
Page 7
ESD-Protected, Low-Voltage, CMOS (V = +5V -5V +25°C, unless otherwise noted ON-RESISTANCE vs (DUAL SUPPLIES) 180 V = +2V CC 160 V = -2V ...
Page 8
... OFF + - -40 - TEMPERATURE (°C) PIN MAX4558 MAX4559 MAX4560 — 12–15 3 — — 11, 12, 14, 15 — 13 — — — — — — — — ...
Page 9
... Don’t care * C not present on MAX4559. Note: Input and output pins are identical and interchangeable. Either may be considered an input or output; signals pass equally well in either direction. _______________________________________________________________________________________ Analog Multiplexers/Switches the X_, Y_, Z_ pins are current limited to a value below the holding current. This ensures that the SCR turns off and normal operation resumes after an ESD event ...
Page 10
... This model consists of a 100pF capacitor charged to the ESD voltage of inter- est, which is then discharged into the test device through a 1.5kΩ resistor. Power-Supply Considerations The MAX4558/MAX4559/MAX4560 are typical of most CMOS analog switches. They have three supply pins and GND. V ...
Page 11
... ESD-Protected, Low-Voltage, CMOS X1–X7 C MAX4558 V ENABLE ENABLE GND X0 X1–X3, Y1–Y3 MAX4559 V ENABLE ENABLE V GND X1, Y1 MAX4560 X0, Y0 ENABLE ENABLE GND EE 50 ...
Page 12
... OUT 35pF V OUT 300 0V V ENABLE V OUT C = 1000pF X0–X3 Y0–Y3 B MAX4559 ENABLE OUT V GND EE 35pF 300 < 20ns R t < 20ns F 50% 80% t BBM OUT OUT V IS THE MEASURED VOLTAGE DUE TO CHARGE OUT TRANSFER ERROR Q WHEN THE CHANNEL TURNS OFF ...
Page 13
... OFF-ISOLATION IS MEASURED BETWEEN COM AND "OFF" NO TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM AND "ON" NO TERMINAL ON EACH SWITCH. CROSSTALK (MAX4559/MAX4560) IS MEASURED FROM ONE CHANNEL X_, Y_ ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 4. Off-Isolation/On-Channel Bandwidth and Crosstalk ...
Page 14
... MAX4558EPE -40°C to +85°C MAX4559CEE 0°C to +70°C MAX4559CSE 0°C to +70°C MAX4559CPE 0°C to +70°C MAX4559EEE -40°C to +85°C MAX4559ESE -40°C to +85°C MAX4559EPE -40°C to +85°C MAX4560CEE 0°C to +70°C MAX4560CSE 0°C to +70°C MAX4560CPE 0°C to +70°C MAX4560EEE -40° ...
Page 15
ESD-Protected, Low-Voltage, CMOS Analog Multiplexers/Switches ______________________________________________________________________________________ Package Information 15 ...
Page 16
... ESD-Protected, Low-Voltage, CMOS Analog Multiplexers/Switches Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...