ADA4051-2 Analog Devices, ADA4051-2 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
ADA4051-2
Manufacturer Part Number
ADA4051-2
Description
1.8V, µPower, Zero-Drift, Rail-to-Rail I/O Amplifier
Manufacturer
Analog Devices
Datasheet
1.ADA4051-1.pdf
(20 pages)
Specifications of ADA4051-2
-3db Bandwidth
200kHz
Slew Rate
40mV/µs
Vos
2µV
Ib
20pA
# Opamps Per Pkg
2
Input Noise (nv/rthz)
95nV/rtHz
Vcc-vee
1.8V to 5.5V
Isy Per Amplifier
13µA
Packages
SOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADA4051-2ACPZ-R7
Manufacturer:
AD
Quantity:
2 000
Company:
Part Number:
ADA4051-2ARMZ
Manufacturer:
ADI
Quantity:
11
Part Number:
ADA4051-2ARMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADA4051-2ARMZ-R7
Manufacturer:
ADI
Quantity:
11
Part Number:
ADA4051-2ARMZ-R7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADA4051-1/ADA4051-2
The design architecture of the ADA4051-1/ADA4051-2
specifically targets precision signal conditioning applications
requiring accurate and stable performance from dc to 10 Hz
bandwidth. In summary, the main features of the ADA4051-1/
ADA4051-2 chopper amplifiers are
•
•
•
•
The ADA4051-1/ADA4051-2 chopper amplifiers provide a rail-
to-rail input range with a 1.8 V to 5.5 V supply voltage range and
20 μA supply current consumption over the −40°C to +125°C
extended industrial temperature range. The gain bandwidth is
125 kHz as a unity-gain stable amplifier up to 100 pF load
capacitance.
INPUT VOLTAGE RANGE
The ADA4051-1/ADA4051-2 have internal ESD protection diodes.
These diodes are connected between the inputs and each supply
rail to protect the input MOSFETs from an electrical discharge
event and are reversed-biased during normal operation. This
protection scheme allows voltages as high as approximately 0.3 V
beyond the supplies (±V
either terminal without causing permanent damage.
If either input exceeds one of the supply rails by more than 0.3 V,
these ESD diodes become forward-biased and large amounts of
current begin to flow through them. Without current limiting, this
excessive current would cause permanent damage to the device.
If the inputs are expected to be subject to overvoltage conditions,
install a resistor in series with each input to limit the input current
to 10 mA maximum.
Considerable suppression of the offset-related ripple
No affect on the desired input signal as long as its
frequency is much lower than the chopping frequency
shown in Figure 60
Achievement of low offset similar to a conventional
chopper amplifier
No introduction of excess noise
SY
± 0.3 V) to be applied at the input of
Rev. B | Page 16 of 20
The ADA4051-1/ADA4051-2 also have internal circuitry that
protects the input stage from high differential voltages. This
circuitry is composed of internal 1.33 kΩ resistors in series with
each input and back-to-back diode-connected N-MOSFET (with a
typical V
normal negative feedback operating conditions, the ADA4051-1/
ADA4051-2 amplifiers correct their output to ensure that the two
inputs are at the same voltage. However, if the device is configured
as a comparator or there are unusual operating conditions, the
input voltages can be forced to different potentials, which may
cause excessive current to flow through the internal diode-
connected N-MOSFETs.
Although the ADA4051-1/ADA4051-2 are rail-to-rail input
amplifiers, take care to ensure that the potential difference
between the inputs does not exceed ±V
damage to the device.
OUTPUT PHASE REVERSAL
Although output phase reversal can occur with other amplifiers
when the input common-mode voltage range is exceeded, the
ADA4051-1/ADA4051-2 amplifiers are designed to prevent
any output phase reversal, provided both inputs are maintained
approximately within 0.3 V above and below the supply voltages
(±V
With other amplifiers, the outputs may jump in the opposite
direction to the supply rail when a common-mode voltage
moves outside the common-mode range. This usually occurs
when one of the internal stages of the amplifier no longer has
sufficient bias voltage across it and subsequently turns off.
However, with the ADA4051-1/ADA4051-2 amplifiers, if one
or both inputs exceed the input voltage range but remain within
the ±V
remains in saturation mode, without phase reversal, until the
input voltage is brought back to within the input voltage range
limits as shown in Figure 55 and Figure 58.
SY
± 0.3 V).
SY
T
± 0.3 V range, an internal loop opens and the output
of 0.7 V for a V
CM
of 0 V) after these series resistors. With
SY
to avert permanent