AD9779 Analog Devices, AD9779 Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9779
Manufacturer Part Number
AD9779
Description
Dual 16-Bit, 1 GSPS, Digital-to-Analog Converter
Manufacturer
Analog Devices
Datasheet
1.AD9778.pdf
(56 pages)
Specifications of AD9779
Resolution (bits)
16bit
Dac Update Rate
1GSPS
Dac Settling Time
n/a
Max Pos Supply (v)
+3.47V
Single-supply
Yes
Dac Type
Current Out
Dac Input Format
Par
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9779ABSV2
Manufacturer:
AD
Quantity:
453
Company:
Part Number:
AD9779ABSVZ
Manufacturer:
ADI
Quantity:
1
Company:
Part Number:
AD9779ABSVZ
Manufacturer:
ADI
Quantity:
184
Company:
Part Number:
AD9779ABSVZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9779ABSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9779ABSVZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD9779BSV
Manufacturer:
ADI
Quantity:
189
Company:
Part Number:
AD9779BSVZ
Manufacturer:
AD
Quantity:
2 100
Company:
Part Number:
AD9779BSVZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9779BSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9779BSVZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9779XSV
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9776/AD9778/AD9779
(Register 0x09, Bits<2:0>) should be set to 111. The PLL control
voltage (Register 0x0A, Bits<7:5>) is read back and is propor-
tional to the dc voltage at the internal loop filter output. With
the PLL bias settings given in this section, the readback from
the PLL control voltage should typically be 010, or possibly 001
or 011. Anything outside of this range indicates that the PLL is
not operating correctly.
The AD977x has an autosearch feature that determines the
optimal settings for the PLL. To enable the autosearch mode, set
Register 0x08, Bits<7:2> to 11111b, and read back the value
from Register 0x08, Bits<7:2>. Autosearch mode is intended to
find the optimal PLL settings only, after which the same settings
should be applied in manual mode. It is not recommended that
the PLL be set to autosearch mode during regular operation.
FULL-SCALE CURRENT GENERATION
Internal Reference
Full-scale current on the I DAC and Q DAC can be set from
8.66 mA to 31.66 mA. Initially, the 1.2 V band gap reference is
used to set up a current in an external resistor connected to
I120 (Pin 75). A simplified block diagram of the reference
circuitry is shown in Figure 77. The recommended value for the
Figure 76. Typical PLL Band Select vs. Frequency over Temperature
60
56
52
48
44
40
36
32
28
24
20
16
12
60
56
52
48
44
40
36
32
28
24
20
16
12
8
4
0
8
4
0
Figure 75. Typical PLL Band Select vs. Frequency at 25°C
F
F
VCO
VCO
(MHz)
(MHz)
Rev. A | Page 38 of 56
external resistor is 10 kΩ, which sets up an I
resistor of 120 μA, which in turn provides a DAC output full-
scale current of 20 mA. Because the gain error is a linear
function of this resistor, a high precision resistor improves gain
matching to the internal matching specification of the devices.
Internal current mirrors provide a current-gain scaling, where
I DAC or Q DAC gain is a 10-bit word in the SPI port register
(Register 0x0A, Register 0x0B, Register 0x0E, and Register 0x0F).
The default value for the DAC gain registers gives an I
approximately 20 mA, where I
0.1μF
Application of Auxiliary DACs in Single Sideband
Transmitter
Two auxiliary DACs are provided on the AD977x. The full-scale
output current on these DACs is derived from the 1.2 V band
gap reference and external resistor. The gain scale from the ref-
erence amplifier current I
current is 16.67 with the auxiliary DAC gain set to full scale
(10-bit values, SPI Register 0x0D and SPI Register 0x11), this
gives a full-scale current of approximately 2 mA for auxiliary
DAC1 and auxiliary DAC2. The auxiliary DAC outputs are not
differential. Only one side of the auxiliary DAC (P or N) is
active at one time. The inactive side goes into a high impedance
state (>100 kΩ). In addition, the P or N outputs can act as
current sources or sinks. The control of the P and N side for
both auxiliary DACs is via Register 0x0E and Register 0x10,
Bits<7:6>. When sourcing current, the output compliance
1
2 .
R
35
30
25
20
15
10
VREF
V
10kΩ
5
0
I120
0
×
⎛
⎜
⎝
27
12
+
200
⎛
⎜
⎝
Figure 78. I
1.2V BAND GAP
Figure 77. Reference Circuitry
1024
AD9779
6
×
REFERENCE
DAC
DAC GAIN CODE
FS
400
vs. DAC Gain Code
FS
Q DAC GAIN
I DAC GAIN
CURRENT
SCALING
is equal to
gain
to the auxiliary DAC reference
⎞
⎟
⎠
600
⎞
× ⎟
⎠
32
REFERENCE
Q DAC
I DAC
800
DAC FULL-SCALE
REFERENCE
CURRENT
in the
FS
1000
of