ATmega1280R212 Atmel Corporation, ATmega1280R212 Datasheet - Page 114
ATmega1280R212
Manufacturer Part Number
ATmega1280R212
Description
Manufacturer
Atmel Corporation
Specifications of ATmega1280R212
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
16 MHz
Max I/o Pins
86
Spi
5
Twi (i2c)
1
Uart
4
Adc Channels
16
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
8
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
6
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
- Current page: 114 of 448
- Download datasheet (8Mb)
15.2.2
2549N–AVR–05/11
EICRB – External Interrupt Control Register B
Table 15-1.
Note:
Table 15-2.
• Bits 7:0 – ISC71, ISC70 - ISC41, ISC40: External Interrupt 7 - 4 Sense Control Bits
The External Interrupts 7 - 4 are activated by the external pins INT7:4 if the SREG I-flag and the
corresponding interrupt mask in the EIMSK is set. The level and edges on the external pins that
activate the interrupts are defined in
before detecting edges. If edge or toggle interrupt is selected, pulses that last longer than one
clock period will generate an interrupt. Shorter pulses are not guaranteed to generate an inter-
rupt. Observe that CPU clock frequency can be lower than the XTAL frequency if the XTAL
divider is enabled. If low level interrupt is selected, the low level must be held until the comple-
tion of the currently executing instruction to generate an interrupt. If enabled, a level triggered
interrupt will generate an interrupt request as long as the pin is held low.
Table 15-3.
Note:
Bit
(0x6A)
Read/Write
Initial Value
ISCn1
ISCn1
Symbol
t
0
0
1
1
0
0
1
1
INT
1. n = 3, 2, 1or 0.
1. n = 7, 6, 5 or 4.
ISCn0
When changing the ISCn1/ISCn0 bits, the interrupt must be disabled by clearing its Interrupt
Enable bit in the EIMSK Register. Otherwise an interrupt can occur when the bits are changed.
When changing the ISCn1/ISCn0 bits, the interrupt must be disabled by clearing its Interrupt
Enable bit in the EIMSK Register. Otherwise an interrupt can occur when the bits are changed.
ISCn0
Minimum pulse width for asynchronous
0
1
0
1
0
1
0
1
Asynchronous External Interrupt Characteristics
Interrupt Sense Control
Interrupt Sense Control
ISC71
R/W
7
0
The falling edge between two samples of INTn generates an interrupt request
The rising edge between two samples of INTn generates an interrupt request
external interrupt
ISC70
R/W
The falling edge of INTn generates asynchronously an interrupt request
The rising edge of INTn generates asynchronously an interrupt request
Parameter
6
0
Any edge of INTn generates asynchronously an interrupt request
Any logical change on INTn generates an interrupt request
ATmega640/1280/1281/2560/2561
ISC61
The low level of INTn generates an interrupt request
The low level of INTn generates an interrupt request
R/W
5
0
(1)
Table
(1)
ISC60
R/W
4
0
15-3. The value on the INT7:4 pins are sampled
Description
ISC51
Description
R/W
Condition
3
0
ISC50
R/W
2
0
Min
ISC41
R/W
1
0
Typ
50
ISC40
R/W
0
0
Max
EICRB
Units
ns
114
Related parts for ATmega1280R212
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika