AT89C5132 Atmel Corporation, AT89C5132 Datasheet - Page 49
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT89C5132
Manufacturer Part Number
AT89C5132
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT89C5132.pdf
(3 pages)
2.AT89C5132.pdf
(182 pages)
3.AT89C5132.pdf
(38 pages)
4.AT89C5132.pdf
(33 pages)
Specifications of AT89C5132
Flash (kbytes)
64 Kbytes
Max. Operating Frequency
20 MHz
Cpu
8051-12C
Max I/o Pins
44
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Uart
1
Adc Channels
2
Adc Resolution (bits)
10
Adc Speed (ksps)
22.7
Sram (kbytes)
2.25
Self Program Memory
API
Operating Voltage (vcc)
2.7 to 3.6
Timers
2
Isp
UART/USB
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
12. Timers/Counters
12.1
12.2
4173E–USB–09/07
Timer/Counter Operations
Timer Clock Controller
The AT89C5132 implement two general-purpose, 16-bit Timers/Counters. They are identified as
Timer 0 and Timer 1, and can be independently configured to operate in a variety of modes as a
Timer or as an event Counter. When operating as a Timer, the Timer/Counter runs for a pro-
grammed length of time, then issues an interrupt request. When operating as a Counter, the
Timer/Counter counts negative transitions on an external pin. After a preset number of counts,
the Counter issues an interrupt request.
The various operating modes of each Timer/Counter are described in the following sections.
For instance, a basic operation is Timer registers THx and TLx (x = 0, 1) connected in cascade
to form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (see Table 40) turns the
Timer on by allowing the selected input to increment TLx. When TLx overflows it increments
THx; when THx overflows it sets the Timer overflow flag (TFx) in TCON register. Setting the TRx
does not clear the THx and TLx Timer registers. Timer registers can be accessed to obtain the
current count or to enter preset values. They can be read at any time but TRx bit must be
cleared to preset their values, otherwise the behavior of the Timer/Counter is unpredictable.
The C/Tx# control bit selects Timer operation or Counter operation by selecting the divided-
down peripheral clock or external pin Tx as the source for the counted signal. TRx bit must be
cleared when changing the mode of operation, otherwise the behavior of the Timer/Counter is
unpredictable.
For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral clock.
The Timer register is incremented once every peripheral cycle (6 peripheral clock periods). The
Timer clock rate is F
For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on the Tx
external input pin. The external input is sampled every peripheral cycles. When the sample is
high in one cycle and low in the next one, the Counter is incremented. Since it takes 2 cycles (12
peripheral clock periods) to recognize a negative transition, the maximum count rate is F
i.e., F
cycle of the external input signal, but to ensure that a given level is sampled at least once before
it changes, it should be held for at least one full peripheral cycle.
As shown in Figure 12-1, the Timer 0 (FT0) and Timer 1 (FT1) clocks are derived from either the
peripheral clock (F
CKCON register. These clocks are issued from the Clock Controller block as detailed in Section
’CKCON Register’, page 14. When T0X2 or T1X2 bit is set, the Timer 0 or Timer 1 clock fre-
quency is fixed and equal to the oscillator clock frequency divided by 2. When cleared, the Timer
clock frequency is equal to the oscillator clock frequency divided by 2 in standard mode or to the
oscillator clock frequency in X2 mode.
OSC
/24 in standard mode or F
PER
PER
) or the oscillator clock (F
/6, i.e., F
OSC
/12 in standard mode or F
OSC
/12 in X2 mode. There are no restrictions on the duty
OSC
) depending on the T0X2 and T1X2 Bits in
OSC
/6 in X2 mode.
AT89C5132
PER
/12,
49