AT32UC3L0128 Atmel Corporation, AT32UC3L0128 Datasheet - Page 839
AT32UC3L0128
Manufacturer Part Number
AT32UC3L0128
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.AT32UC3L0128.pdf
(85 pages)
4.AT32UC3L0128.pdf
(852 pages)
Specifications of AT32UC3L0128
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
50 MHz
Cpu
32-bit AVR
# Of Touch Channels
17
Hardware Qtouch Acquisition
Yes
Max I/o Pins
36
Ext Interrupts
36
Usb Speed
No
Usb Interface
No
Spi
5
Twi (i2c)
2
Uart
4
Lin
4
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
460
Analog Comparators
8
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.62 to 3.6
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
18
Input Capture Channels
12
Pwm Channels
35
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L0128
Manufacturer:
ATMEL
Quantity:
5 709
Company:
Part Number:
AT32UC3L0128-D1HR
Manufacturer:
TOREX
Quantity:
9 000
Company:
Part Number:
AT32UC3L0128-D1HR
Manufacturer:
ATMEL
Quantity:
5 708
Company:
Part Number:
AT32UC3L0128-D3HR
Manufacturer:
ATMEL
Quantity:
400
Part Number:
AT32UC3L0128-D3HR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT32UC3L0128-H
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT32UC3L0128AHEB-UUR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- AT32UC3A0128 PDF datasheet
- AT32UC3A0128 PDF datasheet #2
- AT32UC3L0128 PDF datasheet #3
- AT32UC3L0128 PDF datasheet #4
- Current page: 839 of 852
- Download datasheet (13Mb)
35.3.8
32145A–12/2011
TWI
3. SPI disable does not work in SLAVE mode
4. SPI bad serial clock generation on 2nd chip_select when SCBR=1, CPOL=1, and
5. SPI mode fault detection enable causes incorrect behavior
6. SPI RDR.PCS is not correct
1. TWIS may not wake the device from sleep mode
2. SMBALERT bit may be set after reset
3. Clearing the NAK bit before the BTF bit is set locks up the TWI bus
4. TWIS stretch on Address match error
SPI disable does not work in SLAVE mode.
Fix/Workaround
Read the last received data, then perform a software reset by writing a one to the Software
Reset bit in the Control Register (CR.SWRST).
NCPHA=0
When multiple chip selects (CS) are in use, if one of the baudrates equal 1 while one
(CSRn.SCBR=1) of the others do not equal 1, and CSRn.CPOL=1 and CSRn.NCPHA=0,
then an additional pulse will be generated on SCK.
Fix/Workaround
When multiple CS are in use, if one of the baudrates equals 1, the others must also equal 1
if CSRn.CPOL=1 and CSRn.NCPHA=0.
When mode fault detection is enabled (MR.MODFDIS==0), the SPI module may not operate
properly.
Fix/Workaround
Always disable mode fault detection before using the SPI by writing a one to MR.MODFDIS.
The PCS (Peripheral Chip Select) field in the SPI RDR (Receive Data Register) does not
correctly indicate the value on the NPCS pins at the end of a transfer.
Fix/Workaround
Do not use the PCS field of the SPI RDR.
If the CPU is put to a sleep mode (except Idle and Frozen) directly after a TWI Start condi-
tion, the CPU may not wake upon a TWIS address match. The request is NACKed.
Fix/Workaround
When using the TWI address match to wake the device from sleep, do not switch to sleep
modes deeper than Frozen. Another solution is to enable asynchronous EIC wake on the
TWIS clock (TWCK) or TWIS data (TWD) pins, in order to wake the system up on bus
events.
The SMBus Alert (SMBALERT) bit in the Status Register (SR) might be erroneously set after
system reset.
Fix/Workaround
After system reset, clear the SR.SMBALERT bit before commencing any TWI transfer.
When the TWIS is in transmit mode, clearing the NAK Received (NAK) bit of the Status Reg-
ister (SR) before the end of the Acknowledge/Not Acknowledge cycle will cause the TWIS to
attempt to continue transmitting data, thus locking up the bus.
Fix/Workaround
Clear SR.NAK only after the Byte Transfer Finished (BTF) bit of the same register has been
set.
AT32UC3L0128/256
839
Related parts for AT32UC3L0128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: