AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 1193
AT32UC3C0256C
Manufacturer Part Number
AT32UC3C0256C
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.AT32UC3C0128C.pdf
(1313 pages)
4.AT32UC3C0128C.pdf
(108 pages)
Specifications of AT32UC3C0256C
Flash (kbytes)
256 Kbytes
Pin Count
144
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
123
Ext Interrupts
144
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
7
Twi (i2c)
3
Uart
5
Can
2
Lin
5
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
4
Dac Resolution (bits)
12
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
68
Self Program Memory
YES
External Bus Interface
1
Dram Memory
sdram
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0 to 3.6 or 4.5 to 5.5
Operating Voltage (vcc)
3.0 to 3.6 or 4.5 to 5.5
Fpu
Yes
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
22
Input Capture Channels
12
Pwm Channels
20
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- AT32UC3A0128 PDF datasheet
- AT32UC3A0128 PDF datasheet #2
- AT32UC3C0128C PDF datasheet #3
- AT32UC3C0128C PDF datasheet #4
- Current page: 1193 of 1313
- Download datasheet (20Mb)
39. Programming and Debugging
39.1
39.2
39.2.1
32117C–AVR-08/11
Overview
Service Access Bus
SAB address map
The AT32UC3C supports programming and debugging through two interfaces, JTAG or aWire
JTAG is an industry standard interface and allows boundary scan for PCB testing, as well as
daisy-chaining of multiple devices on the PCB. aWire is an Atmel proprietary protocol which
offers higher throughput and robust communication, and does not require application pins to be
reserved. Either interface provides access to the internal Service Access Bus (SAB), which
offers a bridge to the High Speed Bus, giving access to memories and peripherals in the device.
By using this bridge to the bus system, the flash and fuses can thus be programmed by access-
ing the Flash Controller in the same manner as the CPU.
The SAB also provides access to the Nexus-compliant On-Chip Debug (OCD) system in the
device, which gives the user non-intrusive run-time control of the program execution. Addition-
ally, trace information can be output on the Auxiliary (AUX) debug port or buffered in internal
RAM for later retrieval by JTAG or aWire.
The AVR32 architecture offers a common interface for access to On-Chip Debug, programming,
and test functions. These are mapped on a common bus called the Service Access Bus (SAB),
which is linked to the JTAG and aWire port through a bus master module, which also handles
synchronization between the debugger and SAB clocks.
When accessing the SAB through the debugger there are no limitations on debugger frequency
compared to chip frequency, although there must be an active system clock in order for the SAB
accesses to complete. If the system clock is switched off in sleep mode, activity on the debugger
will restart the system clock automatically, without waking the device from sleep. Debuggers
may optimize the transfer rate by adjusting the frequency in relation to the system clock. This
ratio can be measured with debug protocol specific instructions.
The Service Access Bus uses 36 address bits to address memory or registers in any of the
slaves on the bus. The bus supports sized accesses of bytes (8 bits), halfwords (16 bits), or
words (32 bits). All accesses must be aligned to the size of the access, i.e. halfword accesses
must have the lowest address bit cleared, and word accesses must have the two lowest address
bits cleared.
The Service Access Bus (SAB) gives the user access to the internal address space and other
features through a 36 bits address space. The 4 MSBs identify the slave number, while the 32
LSBs are decoded within the slave’s address space. The SAB slaves are shown in
on page
Table 39-1.
Unallocated
Slave
OCD
HSB
1193.
SAB Slaves, addresses and descriptions.
Address [35:32]
0x0
0x1
0x4
Description
Intentionally unallocated
OCD registers
HSB memory space, as seen by the CPU
AT32UC3C
Table 39-1
1193
™
.
Related parts for AT32UC3C0256C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: