JC075F Lineage Power, JC075F Datasheet - Page 8
JC075F
Manufacturer Part Number
JC075F
Description
Manufacturer
Lineage Power
Datasheet
1.JC075F.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
JC075F1-24
Manufacturer:
LUCENT
Quantity:
27
JC050F, JC075F, JC100F Power Modules: dc-dc Converters;
18 Vdc to 36 Vdc Input, 3.3 Vdc Output; 33 W to 66 W
8 8
Test Configurations
Figure 13.Input Reflected-Ripple Test Setup
Note: Use a 1.0 µF ceramic capacitor and a 10 µF aluminum or
Figure 14.Peak-to-Peak Output Noise
Figure 15. Output Voltage and Efficiency
Note:Measure input reflected-ripple current with a simulated source
Note:All measurements are taken at the module terminals. When
BATTERY
SUPPLY
V
V
tantalum capacitor. Scope measurement should be made
using a BNC socket. Position the load between
51 mm and 76 mm (2 in. and 3 in.) from the module.
RESISTANCE
inductance (L
tery impedance. Measure current as shown above.
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contract resistance.
O
O
CONTACT
(+)
(–)
TO OSCILLOSCOPE
η
Measurement Test Setup
=
Measurement Test Setup
I
I
⎛
⎝
[
------------------------------------------------------ -
TEST
V
COPPER STRIP
[
1.0 µF
V
O
C
ESR < 0.1 Ω
@ 20 ˚C, 100 kHz
S
I
) of 12 µH. Capacitor C
+ ( ) – V
+ ( ) – V
220 µF
V
V
I
I
(+)
(–)
12 µH
L
(
(
TEST
SENSE(+)
SENSE(–)
10 µF
O
I
– ( )
V
– ( )
V
O
O
(+)
(–)
ESR < 0.7 Ω
@ 100 kHz
)
)
]I
]I
33 µF
SCOPE
I
O
⎞ x 100
⎠
CURRENT
DISTRIBUTION LOSSES
PROBE
S
I
O
offsets possible bat-
CONTACT AND
RESISTIVE
LOAD
V
V
8-513 (C).d
LOAD
I
I
8-203 (C).l
(+)
(–)
8-749(C)
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 13, a 33 µF
electrolytic capacitor (ESR < 0.7 Ω at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL-1950, CSA 22.2-950, and EN60950.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements.
If the input meets extra-low voltage (ELV) require-
ments, then the converter’s output is considered ELV.
The input to these units is to be provided with a maxi-
mum 20 A normal-blow fuse in the ungrounded lead.
Electrical Descriptions
Current Limit
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry and can endure current limiting for an unlim-
ited duration. At the point of current-limit inception, the
unit shifts from voltage control to current control. If the
output voltage is pulled very low during a severe fault,
the current-limit circuit can exhibit either foldback or tai-
lout characteristics (output current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Lineage Power
March 2008
Data Sheet