OP470G Analog Devices, OP470G Datasheet
OP470G
Specifications of OP470G
Available stocks
Related parts for OP470G
OP470G Summary of contents
Page 1
... MHz and a slew rate of 2 V/ms. –IN REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices ...
Page 2
... V 110 125 CM = ± 4 ± 0.56 1 125 155 O p (Note 5.5 6.0 –2– OP470F OP470G Min Typ Max Min Typ Max 0.2 0.8 0.4 1 200 80 200 3.8 6.5 3.8 6.5 3.3 5.5 3.3 5.5 3.2 5.0 3.2 5 ...
Page 3
... V/mV 400 800 ± 11 ± ± 12 ± 100 120 dB mV/V 1.0 5.6 — 9 £ £ for OP470G OP470F OP470G Min Typ Max Min Typ Max 0.24 1.0 0.5 1.5 0 600 1400 600 1500 300 700 300 800 ± 11 ± 12 ± ...
Page 4
... Consult factory to negotiate specifications based on dice lot qualification through sample lot assembly and testing unless otherwise noted.) Conditions ± ≥ ± ± 4 ± Load –4– OP470GBC Limit Unit 0.8 mV MAX 20 nA MAX 50 nA MIN 800 V/mV MIN 400 ± MIN ± MIN 100 dB mV/V MAX 5 MAX REV. A ...
Page 5
... P, Y Package . . . . . . . . . . . . . . . . . . . . . . –65∞C to +150∞C Lead Temperature Range (Soldering 60 sec 300∞C Junction Temperature ( –65∞C to +150∞C j Operating Temperature Range OP470A . . . . . . . . . . . . . . . . . . . . . . . . . –55∞C to +125∞C OP470E, OP470F . . . . . . . . . . . . . . . . . . . –25∞C to +85∞C OP470G . . . . . . . . . . . . . . . . . . . . . . . . . . –40∞C to +85∞C ORDERING GUIDE Package Options TA = 25∞C V MAX Cerdip OS ...
Page 6
OP470 –Typical Performance Characteristics 15V I/F CORNER = 5Hz 100 1k FREQUENCY – Hz TPC 1. Voltage Noise Density vs. ...
Page 7
120 V = 15V S 110 100 100 1k 10k 100k 1M FREQUENCY – Hz TPC 10. CMR vs. Frequency 140 T = ...
Page 8
OP470 15V S 24 THD = 10k 100k 1M 10M FREQUENCY – Hz TPC 19. Maximum Output Swing vs. Frequency 360 ...
Page 9
OP470 50k 50 1/4 OP470 CHANNEL SEPARATION = 20 LOG Figure 2. Channel Separation Test Circuit +18V +1V +1V 11 –18V –1V –1V Figure 3. Burn-In Circuit APPLICATIONS ...
Page 10
OP470 Figure 6 shows peak-to-peak noise versus source resistance over the 0 range. Once again, at low values of R voltage noise of the OP470 is the major contributor to peak-to-peak noise with current noise the ...
Page 11
The test time to measure 0 noise should not ex- ceed 10 seconds. As shown in the noise-tester frequency-response curve of Figure 8, the 0.1 Hz corner is defined by only one pole. The test ...
Page 12
OP470 CAPACITIVE LOAD DRIVING AND POWER SUPPLY CONSIDERATIONS The OP470 is unity-gain stable and is capable of driving large capacitive loads without oscillating. Nonetheless, good supply bypassing is highly recommended. Proper supply bypassing reduces problems caused by supply line noise ...
Page 13
Figure 14. Noise Density of Low Noise Amplifier 1000 DIGITAL PANNING CONTROL Figure 15 uses a DAC-8408, quad 8-bit DAC to pan a signal between two channels. The complementary DAC current out- puts two ...
Page 14
OP470 SQUELCH AMPLIFIER The circuit of Figure simple squelch amplifier that uses a FET switch to cut off the output when the input signal falls below a preset limit. The input signal is sampled by a peak ...
Page 15
Cerdip Package (Q-14) 0.005 (0.13) MIN 0.098 (2.49) MAX 14 8 0.310 (7.87) PIN 1 0.220 (5.59 0.100 (2.54) BSC 0.785 (19.94) MAX 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) MAX 0.150 (3.81) 0.200 (5.08) MIN 0.125 (3.18) ...
Page 16
–16– ...