MAX395CWG Maxim Integrated Products, MAX395CWG Datasheet
MAX395CWG
Specifications of MAX395CWG
Available stocks
Related parts for MAX395CWG
MAX395CWG Summary of contents
Page 1
... Dual Supplies +2.7V to +16V Single Supply >2kV ESD Protection per Method 3015.7 TTL/CMOS-Compatible Inputs (with +5V or ±5V Supplies) ______________Ordering Information PART MAX395CNG MAX395CWG MAX395C/D MAX395ENG MAX395EWG MAX395MRG * Contact factory for dice specifications. ** Contact factory for availability. ________________Functional Diagram NO0 ...
Page 2
Serially Controlled, Low-Voltage, 8-Channel SPST Switch ABSOLUTE MAXIMUM RATINGS Voltages Referenced to GND V+ ...........................................................................-0.3V, +17V V- ............................................................................-17V, +0. V-...................................................................-0.3V, +17V SCLK, CS, DIN, DOUT, RESET .................-0.3V to (V+ + 0.3V) NO, COM .................................................(V- - 2V) to (V+ ...
Page 3
Serially Controlled, Low-Voltage, ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) (V+ = +4.5V to +5.5V -4.5V to -5.5V, T PARAMETER SYMBOL SWITCH DYNAMIC CHARACTERISTICS Turn-On Time t ON Turn-Off Time t OFF Break-Before-Make Delay t BBM Charge Injection (Note 4) V ...
Page 4
Serially Controlled, Low-Voltage, 8-Channel SPST Switch TIMING CHARACTERISTICS—Dual Supplies (Figure 1) (V+ = +4.5V to +5.5V -4.5V to -5.5V, T PARAMETER SYMBOL SERIAL DIGITAL INTERFACE SCLK Frequency f SCLK Cycle Time Lead Time ...
Page 5
Serially Controlled, Low-Voltage, ELECTRICAL CHARACTERISTICS—Single +5V Supply (V+ = +4.5V to +5.5V 0V MIN PARAMETER SYMBOL ANALOG SWITCH Analog Signal Range V COM COM, NO On-Resistance Off Leakage Current ...
Page 6
Serially Controlled, Low-Voltage, 8-Channel SPST Switch TIMING CHARACTERISTICS—Single +5V Supply (Figure 1) (V+ = +4.5V to +5.5V 0V MIN PARAMETER SYMBOL SERIAL DIGITAL INTERFACE SERIAL DIGITAL INTERFACE SCLK Frequency f SCLK Cycle ...
Page 7
Serially Controlled, Low-Voltage, ELECTRICAL CHARACTERISTICS—Single +3V Supply (V+ = +3.0V to +3.6V 0V MIN PARAMETER SYMBOL ANALOG SWITCH Analog Signal Range V COM COM, NO On-Resistance Off Leakage Current ...
Page 8
Serially Controlled, Low-Voltage, 8-Channel SPST Switch TIMING CHARACTERISTICS—Single +3V Supply (Figure 1) (V+ = +3.0V to +3.6V 0V MIN PARAMETER SYMBOL SERIAL DIGITAL INTERFACE SCLK Frequency f SCLK Cycle Time (Note 4) ...
Page 9
Serially Controlled, Low-Voltage, __________________________________________Typical Operating Characteristics (V+ = +5V -5V, GND = 0V +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 140 120 V± = ±2.5V 100 V± = ± V± ...
Page 10
Serially Controlled, Low-Voltage, 8-Channel SPST Switch ____________________________Typical Operating Characteristics (continued) (V+ = +5V -5V, GND = 0V +25°C, unless otherwise noted.) A DATA SETUP TIME vs. POSITIVE SUPPLY VOLTAGE 100 ...
Page 11
Serially Controlled, Low-Voltage, _______________Detailed Description Basic Operation The MAX395’s interface can be thought 8-bit shift register controlled by CS (Figure 2). While CS is low, input data appearing at DIN is clocked into the shift register synchronously ...
Page 12
Serially Controlled, Low-Voltage, 8-Channel SPST Switch CS SCLK DIN DATA BITS DOUT DATA BITS FROM PREVIOUS DATA INPUT Figure 2. Three-Wire Interface Timing Table ...
Page 13
Serially Controlled, Low-Voltage, 8x1 Multiplexer To use the MAX395 as an 8x1 multiplexer, connect all common pins together (COM0–COM7) to form the mux output; the mux inputs are NO0–NO7. The mux can be programmed normally, with only one channel selected ...
Page 14
Serially Controlled, Low-Voltage, 8-Channel SPST Switch DIN SCLK CS1 CS2 CS3 CS MAX395 SCLK DIN Figure 6. Addressable Serial Interface D4 SCLK SW4 DIN FOUR CLOCK PULSES Figure 7. Differential Multiplexer Input Control SCLK, each switch sequences one differential channel ...
Page 15
Serially Controlled, Low-Voltage, Table 2. SPDT Switch Programming RESET ...
Page 16
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 1995 Maxim Integrated Products ...