MAX354EPE Maxim Integrated Products, MAX354EPE Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX354EPE
Manufacturer Part Number
MAX354EPE
Description
Multiplexer Switch ICs
Manufacturer
Maxim Integrated Products
Type
Analog Multiplexerr
Datasheet
1.MAX355CWE.pdf
(12 pages)
Specifications of MAX354EPE
Number Of Channels
1 Channel
On Resistance (max)
350 Ohms at +/- 15 V
Propagation Delay Time
250 ns at +/- 15 V
On Time (max)
250 ns at +/- 15 V
Off Time (max)
200 ns at +/- 15 V
Supply Voltage (max)
36 V
Supply Voltage (min)
4.5 V
Maximum Power Dissipation
842 mW
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Package / Case
PDIP N
Mounting Style
Through Hole
Lead Free Status / Rohs Status
No
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX354EPE
Manufacturer:
MAXIM
Quantity:
16
The channel-to-channel switching time is typically
180ns, with about 100ns of break-before-make delay.
This 100ns break-before-make delay prevents the
input-to-input short that would occur if two input chan-
nels were simultaneously connected to the output. In a
typical data acquisition system, the dominant delay is
not the switching time of the multiplexer, but is the set-
tling time of the amplifiers and S/H. Another limiting fac-
tor is the RC time constant of the multiplexer R
the signal source impedance multiplied by the load
capacitance on the output of the multiplexer. Even with
low signal source impedances, 100pF of capacitance
on the multiplexer output will approximately double the
settling time to 0.01% accuracy.
The main effect of supply voltages other than ±15V is
the reduction in output signal range. The MAX354 limits
the output voltage to about 1.5V below V+ and about
3V above V-. In other words, the output swing is limited
to +3.5V to -2V when operating from ±5V. The Typical
Operating Characteristics show R
power supplies. Maxim tests and guarantees the
MAX354/MAX355 for operation from ±4.5V to ±18V
supplies. The switching delays are increased by about
a factor of 2 at ±5V, but break-before-make action is
preserved.
The MAX354/MAX355 can operate with a single +4.5V
to +30V supply, as well as asymmetrical power sup-
plies such as +15V and -5V. The digital threshold
remains approximately 1.6V above the GND pin, and
the analog characteristics, such as R
mined by the total voltage difference between V+ and
V-. Connect V- to 0V when operating with a +4.5V to
+30V single supply.
The MAX354 digital threshold is relatively independent
of the power-supply voltages, going from 1.6V typical
when V+ is 15V to 1.5V typical when V+ is 5V. This
means that the MAX354/MAX355 operate with standard
TTL-logic levels, even with ±5V power supplies. In all
cases, the threshold of the enable (EN) pin is the same
as the other logic inputs.
Fault-Protected Analog Multiplexers
10
______________________________________________________________________________________
Operation with Supply Voltages
ON
Other than ±15V
for +15V and ±5V
ON
, are deter-
ON
plus
The typical digital threshold of both the address lines
and the enable pin is 1.6V, with a temperature coeffi-
cient of about -3mV/°C. This ensures compatibility with
0.8V to 2.4V TTL-logic swings over the entire tempera-
ture range. The digital threshold is relatively indepen-
dent of the supply voltages, moving from 1.6V typical to
1.5V typical as the power supplies are reduced from
±15V to ±5V. In all cases, the digital threshold is refer-
enced to the GND pin.
The digital inputs can also be driven with CMOS-logic
levels swinging from either V+ to V- or from V+ to
ground. The digital input current is just a few nanoamps
of leakage at all input voltage levels, with a guaranteed
maximum of 1µA.
The MAX354/MAX355 function as demultiplexers where
the input is applied to the output pin, and the input pins
are used as outputs. The MAX354/MAX355 provide
both break-before-make action and full fault protection
when operated as demultiplexers, unlike earlier genera-
tions of fault-protected muxes.
At DC and low frequencies the channel-to-channel
crosstalk is caused by variations in output leakage cur-
rents as the off-channel input voltages are varied. The
MAX354 output leakage varies only a few picoamps as
all seven off inputs are toggled from -10V to +10V. The
output voltage change depends on the impedance
level at the MAX354 output, which is R
signal source resistance in most cases, since the load
driven by the MAX354 is usually high impedance. For a
signal source impedance of 10kΩ or lower, the DC
crosstalk exceeds 120dB.
Tables 2a and 2b show typical AC crosstalk and off-
isolation performance. Digital feedthrough is masked
by the analog charge injection when the output is
enabled. When the output is disabled, the digital
feedthrough is virtually unmeasureable, since the digi-
tal pins are physically isolated from the analog section
by the GND and V- pins. The ground plane formed by
these lines is continued onto the MAX354/MAX355 die
to provide over 100dB isolation between the digital and
analog sections.
Off-Isolation, and Digital Feedthrough
Channel-to-Channel Crosstalk,
Operation as a Demultiplexer
Digital Interface Levels
ON
plus the input