DG409DYZ-T Intersil, DG409DYZ-T Datasheet
![IC MULTIPLEXER DUAL 4X1 16SOIC](/photos/5/65/56533/20-16-soic_sml.jpg)
DG409DYZ-T
Specifications of DG409DYZ-T
Related parts for DG409DYZ-T
DG409DYZ-T Summary of contents
Page 1
... DG409DJ DG409DJZ (Note) DG409DJZ DG409DY* DG409DY DG409DYZ* (Note) DG409DYZ DG409DVZ* (Note) DG409DVZ *Add “-T” suffix for tape and reel. **Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. ...
Page 2
Pinouts DG408 (PDIP, SOIC, TSSOP) TOP VIEW Functional Block Diagrams DG408 S ...
Page 3
Pin Descriptions - (DG408) PIN SYMBOL DESCRIPTION 1 A Logic Decode Input (Bit 0, LSB Enable Input 3 V- Negative Power Supply Terminal 4 S Source (Input) for Channel Source (Input) for Channel ...
Page 4
Absolute Maximum Ratings ...
Page 5
Electrical Specifications Test Conditions +15V -15V, V PARAMETER Drain OFF Leakage Current, I D(OFF) DG408 DG409 Drain ON Leakage Current, I D(ON) DG408 DG409 POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ Negative Supply Current, I- Positive ...
Page 6
Test Circuits and Waveforms +15V +2. LOGIC DG408 INPUT GND V- 50Ω - 15V FIGURE 1A. DG408 TEST CIRCUIT SWITCH OUTPUT +15V ...
Page 7
Test Circuits and Waveforms +15V +2.4V V+ ALL S AND DG408 LOGIC DG409 A 1 INPUT GND V- 50Ω - 15V FIGURE 3A. TEST CIRCUIT +15V R V+ GEN S ...
Page 8
Test Circuits and Waveforms 5V +15V SIGNAL 2 GENERATOR GND - 15V ANALYZER INSERTION LOSS = 20 Log FIGURE 7. INSERTION LOSS Typical Applications Overvoltage Protection A very ...
Page 9
Typical Performance Curves 3.5 3 +15V V- = -15V 2.0 1.0 0.5pA 0.0 -1 (V) IN FIGURE 10. INPUT LOGIC CURRENT vs LOGIC INPUT VOLTAGE +15V V- = -15V 60 C D(ON) ...
Page 10
Typical Performance Curves +15V -15V -10 - (V) S FIGURE 16. SOURCE LEAKAGE CURRENT vs SOURCE VOLTAGE ±15V V SUPPLY 2.4V ...
Page 11
Typical Performance Curves - TEMPERATURE (°C) FIGURE 22. POSITIVE SUPPLY CURRENT vs TEMPERATURE (DG408) 120 100 ±15V 20 ±20V 0 -20 -16 - (V) D ...
Page 12
Typical Performance Curves -150 -130 -110 OFF ISOLATION -90 -70 CROSSTALK -50 -30 100 1k 10k 100k FREQUENCY (Hz) FIGURE 28. OFF ISOLATION AND CROSSTALK vs FREQUENCY 200 t TRANS 175 150 125 100 t ON(EN ...
Page 13
Die Characteristics DIE DIMENSIONS: 1800µm x 3320µm x 485µm METALLIZATION: Type: SiAl ±1k Å Å Thickness: 12k Metallization Mask Layout V- ( DG408, DG409 PASSIVATION: Type: Nitride ...
Page 14
Die Characteristics DIE DIMENSIONS: 1800µm x 3320µm x 485µm METALLIZATION: Type: SiAl ±1k Å Å Thickness: 12k Metallization Mask Layout V- ( DG408, DG409 PASSIVATION: Type: Nitride ...
Page 15
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...
Page 16
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 17
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...