PIC32MX440F512H-80V/MR Microchip Technology, PIC32MX440F512H-80V/MR Datasheet - Page 33
![512 KB Flash, 32 KB RAM, USB-OTG, 80 MHz, 10-Bit ADC, DMA 64 QFN 9x9x0.9mm TUBE](/photos/40/62/406286/landingpagemicrochippic32_sml.jpg)
PIC32MX440F512H-80V/MR
Manufacturer Part Number
PIC32MX440F512H-80V/MR
Description
512 KB Flash, 32 KB RAM, USB-OTG, 80 MHz, 10-Bit ADC, DMA 64 QFN 9x9x0.9mm TUBE
Manufacturer
Microchip Technology
Series
PIC® 32MXr
Datasheet
1.TDGL001.pdf
(214 pages)
Specifications of PIC32MX440F512H-80V/MR
Processor Series
PIC32MX4xx
Core
MIPS
Data Bus Width
32 bit
Program Memory Type
Flash
Program Memory Size
512 KB
Data Ram Size
32 KB
Interface Type
USB, I2C, UART, RS-232, RS-485, SPI
Maximum Clock Frequency
80 MHz
Number Of Programmable I/os
5
Number Of Timers
5
Operating Supply Voltage
2.3 V to 3.6 V
Maximum Operating Temperature
+ 105 C
Mounting Style
SMD/SMT
Package / Case
QFN-64
Operating Temperature Range
- 40 C to + 105 C
Supply Current (max)
10 mA
Core Processor
MIPS32® M4K™
Core Size
32-Bit
Speed
80MHz
Connectivity
I²C, IrDA, LIN, PMP, SPI, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
53
Eeprom Size
-
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.3 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Lead Free Status / Rohs Status
Details
2.5
The PGECx and PGEDx pins are used for In-Circuit
Serial Programming™ (ICSP™) and debugging pur-
poses. It is recommended to keep the trace length
between the ICSP connector and the ICSP pins on the
device as short as possible. If the ICSP connector is
expected to experience an ESD event, a series resistor
is recommended, with the value in the range of a few
tens of Ohms, not to exceed 100 Ohms.
Pull-up resistors, series diodes and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger communi-
cations to the device. If such discrete components are
an application requirement, they should be removed
from the circuit during programming and debugging.
Alternately, refer to the AC/DC characteristics and tim-
ing requirements information in the respective device
Flash programming specification for information on
capacitive loading limits and pin input voltage high (V
and input low (V
Ensure that the “Communication Channel Select” (i.e.,
PGECx/PGEDx pins) programmed into the device
matches the physical connections for the ICSP to
MPLAB
For more information on ICD 2, ICD 3 and REAL ICE
connection requirements, refer to the following
documents that are available on the Microchip web
site.
• “MPLAB
• “Using MPLAB
• “MPLAB
• “Using MPLAB
• “MPLAB
• “MPLAB
• “Using MPLAB
2.6
The TMS, TDO, TDI and TCK pins are used for testing
and debugging according to the Joint Test Action
Group (JTAG) standard. It is recommended to keep the
trace length between the JTAG connector and the
JTAG pins on the device as short as possible. If the
JTAG connector is expected to experience an ESD
event, a series resistor is recommended, with the value
in the range of a few tens of Ohms, not to exceed 100
Ohms.
© 2011 Microchip Technology Inc.
Guide” DS51331
User’s Guide” DS51616
®
ICSP Pins
JTAG
ICD 2, MPLAB ICD 3 or MPLAB REAL ICE™.
®
®
®
®
ICD 2 In-Circuit Debugger User’s
ICD 2 Design Advisory” DS51566
ICD 3 Design Advisory” DS51764
REAL ICE™ In-Circuit Debugger
IL
®
®
®
) requirements.
ICD 2” (poster) DS51265
ICD 3” (poster) DS51765
REAL ICE™” (poster) DS51749
IH
)
Pull-up resistors, series diodes and capacitors on the
TMS, TDO, TDI and TCK pins are not recommended
as they will interfere with the programmer/debugger
communications to the device. If such discrete compo-
nents are an application requirement, they should be
removed from the circuit during programming and
debugging. Alternately, refer to the AC/DC characteris-
tics and timing requirements information in the respec-
tive device Flash programming specification for
information on capacitive loading limits and pin input
voltage high (V
2.7
The trace pins can be connected to a hardware-trace-
enabled programmer to provide a compress real time
instruction trace. When used for trace the TRD3,
TRD2, TRD1, TRD0 and TRCLK pins should be dedi-
cated for this use. The trace hardware requires a 22
Ohm series resistor between the trace pins and the
trace connector.
2.8
Many MCUs have options for at least two oscillators: a
high-frequency primary oscillator and a low-frequency
secondary oscillator (refer to
Configuration”
The oscillator circuit should be placed on the same
side of the board as the device. Also, place the
oscillator circuit close to the respective oscillator pins,
not exceeding one-half inch (12 mm) distance
between them. The load capacitors should be placed
next to the oscillator itself, on the same side of the
board. Use a grounded copper pour around the
oscillator circuit to isolate them from surrounding
circuits. The grounded copper pour should be routed
directly to the MCU ground. Do not run any signal
traces or power traces inside the ground pour. Also, if
using a two-sided board, avoid any traces on the
other side of the board where the crystal is placed. A
suggested layout is illustrated in
FIGURE 2-3:
PIC32MX3XX/4XX
Trace
External Oscillator Pins
IH
for details).
) and input low (V
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
Section 8.0 “Oscillator
Figure
IL
) requirements.
DS61143H-page 33
Main Oscillator
Guard Trace
2-3.
Guard Ring
Secondary
Oscillator