CPC5601D Clare, CPC5601D Datasheet - Page 8

• Manufacturer Part Number: CPC5601D
• Description: IC DRVR PROGRAMMABLE 16-SOIC
• Manufacturer: Clare
• Series: CPCr
• Type: Driverr

Specifications of CPC5601D

• Voltage - Supply: 2.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Protocol: -

CPC5601
2.1 Application Circuit Configurations
Figure 4 shows LITELINK II in circuit designed to use
the optical snoop circuit in the CPC5601 for ring
detection. Figure 5 shows LITELINK III in a circuit that
uses the LITELINK snoop circuit ring detection and
display feature (caller ID) signal processing. Note that
either generation of LITELINK can be used with either
signal monitoring scheme. Using the optical path on
the CPC5601 for ring detect precludes on-hook dis-
play feature signal processing.
2.2 AC Termination
The networks connected to outputs b1, b2, b3 and b4
provide selectable telephone line AC termination
depending on which network is switched in place of
R
the application note
information).
In North American applications, turn outputs b1 and
b2 on, and turn outputs b3 and b4 off to switch in the
required 600
tions, turn outputs b1 and b2 off, and outputs b3 and
b4 on to switch in the complex AC termination net-
work.
2.5 Figure 4 Part List
8
1
1
1
1
1
1
2
1
1
ZNT
2.2.1 LITELINK II
Qty.
(see the appropriate
U1
U4
Q1
Q2
DB1
D1
Z1, Z2
SP1
FB1
AC termination. For European applica-
Reference
Understanding LITELINK
LITELINK
CPC561x LITELINK II
CPC5601 Auxiliary Programmable Driver
CPC5602C N-Channel Depletion-Mode FET
MMBT4126 PNP bipolar transistor
S1ZB60 or DB104 Bridge Rectifier
1N914
10V Zener Diode
P3100SB Sidactor
600 , 200 mA ferrite bead
data sheet and
for more
Value
www.clare.com
The networks connected to outputs b1 and b3 provide
selectable telephone line AC termination depending
on which network is switched in place of R
appropriate
note
The resistor connected to output b2 provides the
required bias current for North American applications.
In North American applications, turn outputs b1 and
b2 on, and turn output b3 off to switch in the required
600
outputs b1 and b2 off, and output b3 on to switch in the
complex AC termination network.
2.3 LITELINK III Gain
Turning output 5 on adds attenuation to the receive
path, which is required for the complex termination.
Asserting the MODE pin on LITELINK III corrects for
the added attenuation.
2.4 Current Limiting
Clare recommends using the default value for RZDC
to set the loop-current limit to 133 mA. You can, if
required, adjust the current limit level by adding R73
and using output b6 to switch this value in parallel with
RZDC. See the appropriate LITELINK datasheet for
more information on setting loop-current limits.
2.2.2 LITELINK III
Understanding LITELINK
Clare, Inc.
Fairchild
Sindengen Co., Diodes, Inc.
Teccor, TI, ST Microelectronics
Murata BLM11A601S or similar
AC termination. For European applications, turn
LITELINK
Suppliers
data sheet and the application
for more information).
ZNT
(see the
R3.0