G3NA-440B-DC5-24 Omron Automation, G3NA-440B-DC5-24 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
G3NA-440B-DC5-24
Manufacturer Part Number
G3NA-440B-DC5-24
Description
RELAY; SSR; GEN PURP; CUR-RTG 40A; CTRL-V 5-24DC; VOL-RTG 200-480AC; 4 PIN
Manufacturer
Omron Automation
Datasheet
1.G3NA-210B_DC5-24.pdf
(23 pages)
Specifications of G3NA-440B-DC5-24
Current, Rating
40 A
Function
General Purpose
Number Of Pins
4
Relay Type
Solid State
Standards
UL, CSA, CE, VDE
Voltage, Control
24 VDC
Voltage, Rating
480 VAC
Lead Free Status / Rohs Status
RoHS Compliant part
Solid State Relay (600 VAC)
Engineering Data
High-capacity Heat Sink (Y92B-
P250NF)
DIN-track Mounting
• Assembled DIN Tracks are heavy. Mount the DIN Tracks securely.
• Attach End Plates (PFP-M, order separately) to both ends of the
• To mount a Heat Sink to a DIN Track, press down at the point
Applicable DIN Track
Mounting is possible on TE35-15Fe (IEC 60715) DIN tracks. DIN
tracks from the following manufacturers can be used.
Direct Mounting
• Prepare mounting holes as shown in the diagram.
• When mounting a Heat Sink directly, first remove the Fan Unit, then
• First, temporarily mount the Heat Sink with the bottom two screws
Schneider
WAGO
PHOENIX
Be sure that the Heat Sink is securely locked to the DIN Track.
Units on the DIN Track to hold them in place.
indicated by arrow 1 in the diagram and then press in the Heat Sink
at the point indicated by arrow 2.
Manufacturer
Tightening torque: 0.98 to 1.47 N⋅m
mount the Heat Sink by itself before attaching the Fan Unit again.
(Remove the two screws shown in the following diagram.)
and then attach the top two screws with the mounting bracket
sandwiched between the Heat Sink and mounting surface. Finally,
tighten all four screws.
Remove screws
AM1-DE2000
210-114 or 210-197
N35/15
Vertical
Thickness: 1.5 mm
G3NA-6
130
Heat Sink
±0.3
Four, 4.5 dia. or M4 holes
Fan Unit
64
±0.3
---
210-118
N35/15/15-2.3
Thickness: 2.3 mm
Ratings and Characteristics of High-
capacity Heat Sink (Y92B-P250NF)
Fan Ratings
Note: Average values.
Thermostat Ratings
Fan/Thermostat Characteristics
• Use a commercial power supply (50/60 Hz) for the Fan.
• Be sure to turn OFF the power supply and wait for the blades to
• High-precision ball bearings are used in the fan and these may be
• The life of the Fan depends on the ambient temperature, As a
• Be sure there are no objects near the air vents that would restrict
• The Fan is an OMRON R87F-A4A-93HP (200 VAC) Fan. Use the
• The recommended tightening torque for the Fan is 0.44 N⋅m.
• Terminals equivalent to Faston #110 are used for the Fan power
• Refer to the following table for the OMRON Fan power supply plug
• Connect the ground screw hole on the fan to PE.
Rated voltage
Operating voltage
Frequency
Rated current
(See note.)
Rated speed
(See note.)
Operating temperature Approx. 90°C
Contact ratings
Motor type
Terminal type
Insulation class
Insulation
resistance
Insulation
withstand voltage
Ambient operating
temperature
Ambient storage
temperature
Ambient humidity
Protection
Materials
Bearings
Weight
Compliant standards PSE, EN/IEC 60335 (CE marking compliant)
Certified standards UL/CSA (pending)
1 m
2 m
stop before inspecting the Fan.
damaged if the Fan is dropped or otherwise subjected to shock.
The life and characteristics of the Fan will be reduced if the
bearings are damaged. Do not subject the Fan to shock.
guideline, the Fan life is 40,000 hours for continuous usage at
40°C.
air flow and no loose objects, such as electrical lines.
same model of Fan for replacement.
supply terminals.
cables (order separately).
length
Cable
R87F-PC
R87F-PC-20
UL certified
Single-phase shading coil induction motor
(2-pole, open type)
Terminals
IEC class B (130°C)
UL class A (105°C)
CSA class A (105°C)
100 MΩ min. (at 500 VDC) between all power
supply connections and uncharged metal parts.
2,000 VAC (1 minute) between all power supply
connections and uncharged metal parts.
−30 to 70°C (no icing)
−40 to 85°C (no icing)
25 to 85%
Impedance protection
Frame : Die-cast aluminum
Blades : Glass polycarbonate
Ball bearings
Approx. 300 g
200 V
85% to 110% of rated voltage
50/60 Hz
0.061 A at 50 Hz
0.052 A at 60 Hz
2,600 r/min at 50 Hz
3,050 r/min at 60 Hz
3 A at 240 VAC, resistive load
3 A at 24 VDC, resistive load
R87F-PCJT
R87F-PCJT-20
Complies with Electrical Appliance
and Material Safety Law (Japan)
G3NA
11