S-8241ADLMC-GDLT2G Seiko Instruments, S-8241ADLMC-GDLT2G Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/5/590/seiko_instruments_sml.jpg)
S-8241ADLMC-GDLT2G
Manufacturer Part Number
S-8241ADLMC-GDLT2G
Description
Battery Management Lithium-Ion battery protection (1 cell)
Manufacturer
Seiko Instruments
Datasheet
1.S-8241ABPMC-GBPT2G.pdf
(38 pages)
Specifications of S-8241ADLMC-GDLT2G
Product
Li-Ion Protection
Battery Type
Li-Ion, Li-Pol Packs
Output Voltage
4.22 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Package / Case
SOT-23
Mounting Style
SMD/SMT
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
26
BATTERY PROTECTION IC FOR 1-CELL PACK
S-8241 Series
Battery Protection IC Connection Example
*1. If an FET with a threshold voltage of 0.4 V or lower is used, the FET may fail to cut the charging current.
*2. If the withstand voltage between the gate and source is lower than the charger voltage, the FET may break.
*3. If R1 has a higher resistance than R2 and if a charger is connected reversely, current flows from the charger to the IC and the
*4. If a capacitor C1 is less than 0.01 μF, DO may oscillate when load short-circuiting is detected, a charger is connected
*5. If R2 is set to less than 300 Ω, a current which is bigger than the power dissipation flows through the IC and the IC may break
Caution 1. The above constants may be changed without notice.
Symbol
FET1
FET2
R1
C1
R2
If an FET with a threshold voltage equal to or higher than the overdischarge detection voltage is used, discharging may stop
before overdischarge is detected.
voltage between VDD and VSS may exceed the absolute maximum rating. Install a resistor of 300 Ω or higher as R1 for ESD
protection.
If R1 has a high resistance, the overcharge detection voltage increases by IC current consumption.
reversely, or overcurrent 1 or 2 is detected.
A capacitor of 0.01 μF or higher as C1 should be installed. In some types of batteries DO oscillation may not stop unless the
C1 capacity is increased. Set the C1 capacity by evaluating the actual application.
when a charger is connected reversely. If a resistor bigger than 1.3 kΩ is installed as R2, the charging current may not be cut
when a high-voltage charger is connected.
2. It has not been confirmed whether the operation is normal or not in circuits other than the above example
Nch
MOS_FET
Nch
MOS_FET
Capacitor
Resistor
Resistor
of connection. In addition, the example of connection shown above and the constant do not guarantee
proper operation. Perform thorough evaluation using the actual application to set the constant.
Parts
Protection for ESD and
power fluctuation
Protection for power
fluctuation
Protection for charger
reverse connection
Battery C1 :
Discharge control
R1 : 470 Ω
Charge control
Purpose
0.1 μF
Table 16 Constants for External Components
VDD
VSS
Seiko Instruments Inc.
DO
0.1 μF
470 Ω
FET1
1 kΩ
Typ.
S-8241 Series
⎯
⎯
Figure 12
CO
0.01 μF
300 Ω
300 Ω
min.
FET2
⎯
⎯
R2 value
VM
1.0 μF
1.3 kΩ
max.
⎯
⎯
R2 : 1 kΩ
0.4 V ≤ Threshold voltage ≤
overdischarge detection voltage.
Withstand voltage between gate and
source ≥ Charger voltage
0.4 V ≤ Threshold voltage ≤
overdischarge detection voltage.
Withstand voltage between gate and
source ≥ Charger voltage
Relation R1 ≤ R2 should be
maintained.
Install a capacitor of 0.01 μF or
higher between VDD and VSS.
To suppress current flow caused by
reverse connection of a charger, set the
resistance within the range from 300 Ω to
1.3 kΩ.
*5
EB+
EB−
*3
Remarks
*2
*2
Rev.9.0
*4
*1
*1
_00