ATF22V10C-10SU Atmel, ATF22V10C-10SU Datasheet
![IC PLD 10NS 24-SOIC](/photos/6/70/67046/453-24-soic_sml.jpg)
ATF22V10C-10SU
Specifications of ATF22V10C-10SU
Available stocks
Related parts for ATF22V10C-10SU
ATF22V10C-10SU Summary of contents
Page 1
... Description ® The Atmel ATF22V10C is a high-performance CMOS (electrically erasable) pro- grammable logic device (PLD) that utilizes proven electrically erasable Flash memory technology from Atmel. Speeds down to 5ns and power dissipation as low as 10µA (typical) are offered. All speed ranges are specified over the full 5V ± 10% range for military and industrial temperature ranges, and 5V ± ...
Page 2
... IN 11 GND 12 Figure 2-3. PLCC/LCC IN/ GND Note: For all PLCCs (except “-5”), pins and 22 can be left unconnected. However, if they are connected, superior performance will be achieved Atmel ATF22V10C(Q) 2 Figure 2-2. CLK/IN 24 VCC 23 I/O 22 I/O IN/PD 21 I/O 20 I/O 19 I/O 18 I/O 17 I/O 16 I/O ...
Page 3
... Maximum output pin voltage is V may overshoot to 7.0V for pulses of less than 20ns. (1) Commercial Industrial 0°C - 70°C -40°C - 85°C 5V± 5% 5V± 10% Atmel ATF22V10C(Q) + 0.75V DC, which CC Military -55°C - 125°C (case) 5V± 10% 3 ...
Page 4
... Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec (1) 4.2 AC Waveforms CLOCK Note: 1. Timing measurement reference is 1.5V. Input AC driving levels are 0.0V and 3.0V, unless otherwise specified Atmel ATF22V10C(Q) 4 Condition 0 V V (Max 3.5 ...
Page 5
... Atmel ATF22V10C(Q) -7 -10 Max Min Max Min 7.5 3.0 10.0 (2) 4.5 2.0 6.5 2.5 2.5 4.5 10 (3) 90.0 55.5 117.0 80 ...
Page 6
... Input Test Waveforms and Measurement Levels 4.5.2 Commercial Output Test Loads 4.6 Pin Capacitance Table 4-1. Pin Capacitance (f = 1MHz OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested Atmel ATF22V10C(Q) 6 (1)(2)( Min Max Min 5.0 7 ...
Page 7
... Preload of Registered Outputs The ATF22V10C registers are provided with circuitry to allow loading of each register with either a high or a low. This feature will simplify testing since any state can be forced into the registers to control test sequencing. A JEDEC file with preload is generated when a source file with vectors is compiled. Once downloaded, the JEDEC file preload sequence will be done automatically by most of the approved programmers after the programming ...
Page 8
... The Atmel ATF22V10C contains internal input and I/O pin-keeper circuits. These circuits allow each ATF22V10C pin to hold its previous value even when it is not being driven by an external source or by the device’s output buffer. This helps to ensure that all logic array inputs are at known valid logic levels. This reduces system power by preventing pins from floating to indeterminate levels ...
Page 9
... ATF22V10C (PLCC) WINCUPL P22V10 P22V10LCC Note: 1. These device types will create a JEDEC file which when programmed in Atmel ATF22V10C devices will enable the power-down mode feature. All other device types have the feature disabled 0735U–PLD–7/10 PAL Mode GAL Mode (5892 Fuses) ...
Page 10
... Functional Logic Diagram Atmel ATF22V10C(Q) 10 0735U–PLD–7/10 ...
Page 11
... TEMPERATURE (°C) ATMEL ATF22V10C/CQ OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE (V 0.0 0.5 1.0 1.5 2.0 2.5 3.0 V (V) OH ATMEL ATF22V10C/CQ OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE (V = 0.5V) OL 0.0 0.5 1.0 1.5 2.0 2.5 3.0 SUPPLY VOLTAGE (V) ATMEL ATF22V10C/CQ INPUT CLAMP CURRENT VS. INPUT VOLTAGE (V ...
Page 12
... NORMALIZED T VS. TEMPERATURE SU -40.0 0.0 25.0 TEMPERATURE (°C) ATMEL ATF22V10C/CQ DELTA T VS. OUTPUT LOADING 100 150 200 OUTPUT LOADING (pF) ATMEL ATF22V10C/CQ DELTA T NUMBER OF OUTPUT SWITCHING 1.0 2.0 3.0 4.0 5.0 6.0 7.0 NUMBER OF OUTPUTS SWITCHING 75.0 75.0 250 300 VS. PD 8.0 9 ...
Page 13
... NUMBER OF OUTPUTS LOADING 0735U–PLD–7/10 0.0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 200 250 300 Atmel ATF22V10C(Q) ATMEL ATF22V10C/CQ DELTA T VS. NUMBER OF SWITCHING CO 1.0 2.0 3.0 4.0 5.0 6.0 7.0 NUMBER OF OUTPUTS SWITCHING 8.0 9.0 10.0 13 ...
Page 14
... Wide, Plastic Thin Shrink Small Outline (TSSOP) 28J 28-lead, Plastic J-leaded Chip Carrier (PLCC) 28L 28-lead, Ceramic Leadless Chip Carrier (LCC) Atmel ATF22V10C(Q) 14 (ns) Ordering Code 4 ATF22V10C-5JX ATF22V10C-7PX ATF22V10C-7SX ATF22V10C-7JU ATF22V10C-10JU ATF22V10C-10PU ATF22V10C-10SU ATF22V10C-10XU ATF22V10C-15JU ATF22V10C-15PU 8 ATF22V10CQ-15JU (1) (ns) Ordering Code ATF22V10C-10GM/883 ATF22V10C-10NM/883 5962-8984116LA 5962-89841163A ATF22V10C-15GM/883 ATF22V10C-15NM/883 8 ...
Page 15
... PIN 1 27.94(1.100) REF 1.65(0.065) 1.14(0.045) 8.13(0.320) 7.37(0.290) 0º~ 15º REF 10.20(0.400) MAX TITLE 24D3, 24-lead, 0.300" Wide. Non-windowed, Ceramic Dual Inline Package (Cerdip) Atmel ATF22V10C(Q) 7.87(0.310) 7.24(0.285) 0.127(0.005) MIN 1.52(0.060) 0.38(0.015) 0.66(0.026) 0.36(0.014) DRAWING NO. 24D3 10/21/03 REV ...
Page 16
... A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-001, Variation AF 2. Dimensions D and E1 do not include mold Flash or Protrusion Mold Flash or Protrusion shall not exceed 0.25mm (0.010") Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22V10C( PIN TITLE 24P3, 24-lead (0.300"/7.62mm Wide) Plastic Dual ...
Page 17
... SOIC PIN 1 ID PIN Package Drawing Contact: packagedrawings@atmel.com 0735U–PLD–7/ TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) Atmel ATF22V10C(Q) COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A – – 2.65 A1 0.10 – 0.30 D 10.00 – 10.65 D1 7.40 – ...
Page 18
... TSSOP Dimensions in Millimeter and (Inches)* JEDEC STANDARD MO-153 AD Controlling dimension: millimeters PIN 1 0 Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22V10C(Q) 18 0.30(0.012) 0.19(0.007) 4.48(0.176) 4.30(0.169) 0.65(0.0256)BSC 7.90(0.311) 7.70(0.303) 0.15(0.006) 0.05(0.002) 8 0.75(0.030) 0.45(0.018) TITLE 24X, 24-lead (4.4mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) 6 ...
Page 19
... Lead coplanarity is 0.004" (0.102mm) maximum Package Drawing Contact: packagedrawings@atmel.com 0735U–PLD–7/10 1.14(0.045) X 45° PIN NO. 1 IDENTIFIER SYMBOL TITLE 28J, 28-lead, Plastic J-leaded Chip Carrier (PLCC) Atmel ATF22V10C(Q) 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX NOM NOTE A 4.191 – ...
Page 20
... LCC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 C-4 11.68(0.460) 11.23(0.442) 7.62(0.300) BSC 1.27(0.050) TYP Package Drawing Contact: packagedrawings@atmel.com Atmel ATF22V10C(Q) 20 11.68(0.460) 11.23(0.442) PIN 1 1.40(0.055) INDEX CORNER 1.14(0.045) 2.41(0.095) 1.91(0.075) 0.635(0.025) 0.381(0.015) 0.305(0.012) 0.178(0.007) 0.737(0.029) 0.533(0.021) 1.02(0.040) X 45° ...
Page 21
... C-15 and CQ-15 Commercial part removed from Removed Mil from I , C-15 (Ind.) parts 15mhz Max changed from 90mA to 125mA CC2 Added military-grade packages and removed leaded parts Added new green part Updated Green package options Atmel ATF22V10C(Q) Table 4-1. 21 ...
Page 22
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...