EP2AGX65DF29C6N Altera, EP2AGX65DF29C6N Datasheet - Page 113

• Manufacturer Part Number: EP2AGX65DF29C6N
• Description: IC ARRIA II GX FPGA 65K 780FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX65DF29C6N

• Number Of Logic Elements/cells: 60214
• Number Of Labs/clbs: 2530
• Total Ram Bits: 5246
• Number Of I /o: 364
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-FBGA
• Family Name: Arria® II GX
• Number Of Logic Blocks/elements: 63250
• # I/os (max): 364
• Frequency (max): 400MHz
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 63250
• Ram Bits: 5557452.8
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Chapter 5: Clock Networks and PLLs in Arria II GX Devices
PLLs in Arria II GX Devices
Clock Multiplication and Division
© July 2010
Altera Corporation
Figure 5–16
ZDB mode.
Figure 5–16. Phase Relationship Between PLL Clocks in Zero Delay Buffer Mode
Note to
(1) The internal PLL clock output can lead or lag the external PLL clock outputs.
Each Arria II GX PLL provides clock synthesis for PLL output ports with
M/(N  post-scale counter) scaling factors. The input clock is divided by a pre-scale
factor, n, and is then multiplied by the m feedback factor. The control loop drives the
VCO to match f
divides down the high-frequency VCO. For multiple PLL outputs with different
frequencies, the VCO is set to the least common multiple of the output frequencies
that meets its frequency specifications. For example, if output frequencies required
from one PLL are 33 and 66 MHz, the Quartus II software sets the VCO to 660 MHz
(the least common multiple of 33 and 66 MHz in the VCO range). Then the post-scale
counters scale down the VCO frequency for each output port.
The VCO frequency reported by the Quartus II software is the value after the
post-scale counter divider, k.
Each PLL has one pre-scale counter, n, and one multiply counter, m, with a range of
1 to 512 for both m and n. The n counter does not use duty-cycle control because the
only purpose of this counter is to calculate frequency division. There are seven generic
post-scale counters in each PLL that can feed GCLKs, RCLKs, or external clock
outputs. These post-scale counters range from 1 to 512 with a 50% duty cycle setting.
The high- and low-count values for each counter ranges from 1 to 256. The sum of the
high- and low-count values chosen for a design selects the divide value for a given
counter.
The Quartus II software automatically chooses the appropriate scaling factors
according to the input frequency, multiplication, and division values entered into the
ALTPLL megafunction.
Figure
Register Clock Port
5–16:
Clock Outputs (1)
shows an example waveform of the PLL clocks’ phase relationship in
PLL Clock at the
Dedicated PLL
in
(M/N). Each output port has a unique post-scale counter that
PLL Reference
Clock at the
Input Pin
Phase Aligned
Arria II GX Device Handbook, Volume 1
5–21