EP3SL150F780C4N Altera, EP3SL150F780C4N Datasheet - Page 193

• Manufacturer Part Number: EP3SL150F780C4N
• Description: IC STRATIX III FPGA 150K 780FBGA
• Manufacturer: Altera
• Series: Stratix® IIIr

Specifications of EP3SL150F780C4N

• Number Of Logic Elements/cells: 142500
• Number Of Labs/clbs: 5700
• Total Ram Bits: 6390
• Number Of I /o: 488
• Voltage - Supply: 0.86 V ~ 1.15 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 780-FBGA
• Family Name: Stratix III
• Number Of Logic Blocks/elements: 142500
• # I/os (max): 488
• Frequency (max): 450MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.1V
• Logic Cells: 142500
• Ram Bits: 6543360
• Operating Supply Voltage (min): 1.05V
• Operating Supply Voltage (max): 1.15V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FC-FBGA
• For Use With: 544-2568 - KIT DEVELOPMENT STRATIX III
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2403; EP3SL150F780C4NES

Chapter 6: Clock Networks and PLLs in Stratix III Devices
PLLs in Stratix III Devices
Figure 6–41. PLL Reconfiguration Waveform
© July 2010
CONFIGUPDATE
SCANDATAOUT
SCANCLKENA
SCANDONE
SCANDATA
SCANCLK
ARESET
Altera Corporation
1
Figure 6–41
When you reconfigure the counter clock frequency, you cannot reconfigure the
corresponding counter phase shift settings using the same interface. Instead,
reconfigure the phase shifts in real time using the dynamic phase shift reconfiguration
interface. If you reconfigure the counter frequency, but wish to keep the same
non-zero phase shift setting (for example, 90 degrees) on the clock output, you must
reconfigure the phase shift immediately after reconfiguring the counter clock
frequency.
Post-Scale Counters (C0 to C9)
The multiply or divide values and duty cycle of post-scale counters can be
reconfigured in real time. Each counter has an 8-bit high-time setting and an 8-bit
low-time setting. The duty cycle is the ratio of output
high- or low-time to the total cycle time, which is the sum of the two. Additionally,
these counters have two control bits, rbypass, for bypassing the counter, and
rselodd, to select the output clock duty cycle.
When the rbypass bit is set to 1, it bypasses the counter, resulting in a divide by 1.
When this bit is set to 0, the high- and low-time counters are added to compute the
effective division of the VCO output frequency. For example, if the post-scale divide
factor is 10, the high- and low-count values could be set to 5 and 5, respectively, to
achieve a 50-50% duty cycle. The PLL implements this duty cycle by transitioning the
output clock from high to low on the rising edge of the VCO output clock. However, a
4 and 6 setting for the high- and low-count values, respectively, would produce an
output clock with 40-60% duty cycle.
Dn_old
Dn
shows a functional simulation of the PLL reconfiguration feature.
D0_old
D0
Stratix III Device Handbook, Volume 1
Dn
6–45