EP2C8Q208C8 Altera, EP2C8Q208C8 Datasheet - Page 79

IC CYCLONE II FPGA 8K 208-PQFP

EP2C8Q208C8

Manufacturer Part Number
EP2C8Q208C8
Description
IC CYCLONE II FPGA 8K 208-PQFP
Manufacturer
Altera
Series
Cyclone® IIr
Datasheet

Specifications of EP2C8Q208C8

Number Of Logic Elements/cells
8256
Number Of Labs/clbs
516
Total Ram Bits
165888
Number Of I /o
138
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
208-MQFP, 208-PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-1456

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EP2C8Q208C8
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP2C8Q208C8
Manufacturer:
ALTERA
0
Part Number:
EP2C8Q208C8
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Part Number:
EP2C8Q208C8N
Manufacturer:
ALTERA
Quantity:
8
Part Number:
EP2C8Q208C8N
Manufacturer:
ALTERA
Quantity:
853
Part Number:
EP2C8Q208C8N
Manufacturer:
Altera
Quantity:
10 000
Part Number:
EP2C8Q208C8N
Manufacturer:
ALTERA
0
Part Number:
EP2C8Q208C8N
Manufacturer:
ALTERA
Quantity:
14 945
Part Number:
EP2C8Q208C8N
0
SignalTap II
Embedded Logic
Analyzer
Configuration
Operating
Modes
Altera Corporation
February 2007
f
Cyclone II devices support the SignalTap II embedded logic analyzer,
which monitors design operation over a period of time through the IEEE
Std. 1149.1 (JTAG) circuitry. You can analyze internal logic at speed
without bringing internal signals to the I/O pins. This feature is
particularly important for advanced packages, such as FineLine BGA
packages, because it can be difficult to add a connection to a pin during
the debugging process after a board is designed and manufactured.
For more information on the SignalTap II, see the Signal Tap chapter of
the Quartus II Handbook, Volume 3.
The logic, circuitry, and interconnects in the Cyclone II architecture are
configured with CMOS SRAM elements. Altera FPGA devices are
reconfigurable and every device is tested with a high coverage
production test program so you do not have to perform fault testing and
can instead focus on simulation and design verification.
Cyclone II devices are configured at system power-up with data stored in
an Altera configuration device or provided by a system controller. The
Cyclone II device’s optimized interface allows the device to act as
controller in an active serial configuration scheme with EPCS serial
configuration devices. The serial configuration device can be
programmed via SRunner, the ByteBlaster II or USB Blaster download
cable, the Altera Programming Unit (APU), or third-party programmers.
In addition to EPCS serial configuration devices, Altera offers in-system
programmability (ISP)-capable configuration devices that can configure
Cyclone II devices via a serial data stream using the Passive serial (PS)
configuration mode. The PS interface also enables microprocessors to
treat Cyclone II devices as memory and configure them by writing to a
virtual memory location, simplifying reconfiguration. After a Cyclone II
device has been configured, it can be reconfigured in-circuit by resetting
the device and loading new configuration data. Real-time changes can be
made during system operation, enabling innovative reconfigurable
applications.
The Cyclone II architecture uses SRAM configuration elements that
require configuration data to be loaded each time the circuit powers up.
The process of physically loading the SRAM data into the device is called
configuration. During initialization, which occurs immediately after
configuration, the device resets registers, enables I/O pins, and begins to
operate as a logic device. You can use the 10MHz internal oscillator or the
optional CLKUSR pin during the initialization. The 10 MHz internal
oscillator is disabled in user mode. Together, the configuration and
initialization processes are called command mode. Normal device
operation is called user mode.
Cyclone II Device Handbook, Volume 1
Configuration & Testing
®
3–5

Related parts for EP2C8Q208C8