AD9775BSV Analog Devices Inc, AD9775BSV Datasheet - Page 29
![IC DAC 14BIT DUAL 160MSPS 80TQFP](/photos/6/64/66419/505-80-tqfp_sml.jpg)
AD9775BSV
Manufacturer Part Number
AD9775BSV
Description
IC DAC 14BIT DUAL 160MSPS 80TQFP
Manufacturer
Analog Devices Inc
Series
TxDAC+®r
Datasheet
1.AD9775BSVZRL.pdf
(56 pages)
Specifications of AD9775BSV
Rohs Status
RoHS non-compliant
Settling Time
11ns
Number Of Bits
14
Data Interface
Parallel
Number Of Converters
2
Voltage Supply Source
Analog and Digital
Power Dissipation (max)
410mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
For Use With
AD9775-EBZ - BOARD EVALUATION FOR AD9775
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9775BSV
Manufacturer:
AD
Quantity:
1 831
Company:
Part Number:
AD9775BSV
Manufacturer:
ADI
Quantity:
329
Part Number:
AD9775BSV
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9775BSVZ
Manufacturer:
Analog Devices Inc
Quantity:
135
Company:
Part Number:
AD9775BSVZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9775BSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9775BSVZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
DATACLK INVERSION
(Control Register 0x02, Bit 4)
By programming this bit, the DATACLK signal shown in
Figure 52 can be inverted. With inversion enabled, t
the time between the rising edge of CLKIN and the falling edge
of DATACLK. No other effect on timing occurs.
DATA AT PORTS
DATACLK DRIVER STRENGTH
(Control Register 0x02, Bit 5)
The DATACLK output driver strength is capable of driving
>10 mA into a 330 Ω load while providing a rise time of 3 ns.
Figure 53 shows DATACLK driving a 330 Ω resistive load at a
frequency of 50 MHz. By enabling the drive strength option
(Control Register 0x02, Bit 5), the amplitude of DATACLK
under these conditions increases by approximately 200 mV.
Figure 52. Timing Requirements in Two-Port Input Mode, with PLL Enabled
–0.5
3.0
2.5
2.0
1.5
1.0
0.5
1 AND 2
0
0
Figure 53. DATACLK Driver Capability into 330 Ω at 50 MHz
DATACLK
CLKIN
10
t
S
t
H
20
t
OD
TIME (ns)
DELTA APPROX. 2.8ns
30
t
t
t
OD
S
H
= 0.0ns (MIN)
= 2.5ns (MIN)
= 1.5ns (MIN) TO 2.5ns (MAX)
40
OD
refers to
50
Rev. E | Page 29 of 56
PLL ENABLED, ONE-PORT MODE
(Control Register 0x02, Bit 6 to Bit 1 and
Control Register 0x04, Bit 7 to Bit 1)
In one-port mode, the I and Q channels receive their data from an
interleaved stream at digital input Port 1. The function of Pin 32 is
defined as an output (ONEPORTCLK) that generates a clock at the
interleaved data rate, which is 2× the internal input data rate of the I
and Q channels. The frequency of CLKIN is equal to the internal
input data rate of the I and Q channels. The selection of the data for
the I or the Q channel is determined by the state of the logic level at
Pin 31 (IQSEL when the AD9775 is in one-port mode) on the
rising edge of ONEPORTCLK. Under these conditions, IQSEL = 0
latches the data into the I channel on the clock rising edge, while
IQSEL = 1 latches the data into the Q channel. It is possible to
invert the I and Q selection by setting Control Register 0x02, Bit 1
to the invert state (Logic 1). Figure 54 illustrates the timing
requirements for the data inputs as well as the IQSEL input. Note
that the 1× interpolation rate is not available in the one-port mode.
The DAC output sample rate in one-port mode is equal to
CLKIN multiplied by the interpolation rate. If zero stuffing is
used, another factor of 2 must be included to calculate the DAC
sample rate.
ONEPORTCLK INVERSION
(Control Register 0x02, Bit 2)
By programming this bit, the ONEPORTCLK signal shown in
Figure 54 can be inverted. With inversion enabled, t
the delay between the rising edge of the external clock and the
falling edge of ONEPORTCLK. The setup and hold times, t
and t
There is no other effect on timing.
INPUT DATA AT PORT 1
I AND Q INTERLEAVED
H
, are with respect to the falling edge of ONEPORTCLK.
ONEPORTCLK
CLKIN
IQSEL
Figure 54. Timing Requirements in One-Port
Input Mode with the PLL Enabled
t
IQS
t
OD
t
S
t
H
t
IQH
t
t
t
t
t
OD
S
H
IQS
IQH
= 3.0ns (MIN)
= –0.5ns (MIN)
= 4.0ns (MIN)
= 3.5ns (MIN)
= –1.5ns (MIN)
TO 5.5ns (MAX)
OD
AD9775
refers to
S