MT47H32M16BN-37E:D Micron Technology Inc, MT47H32M16BN-37E:D Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT47H32M16BN-37E:D
Manufacturer Part Number
MT47H32M16BN-37E:D
Description
Manufacturer
Micron Technology Inc
Type
DDR2 SDRAMr
Datasheet
1.MT47H32M16BN-37ED.pdf
(139 pages)
Specifications of MT47H32M16BN-37E:D
Organization
32Mx16
Density
512Mb
Address Bus
15b
Access Time (max)
500ps
Maximum Clock Rate
533MHz
Operating Supply Voltage (typ)
1.8V
Package Type
FBGA
Operating Temp Range
0C to 85C
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Supply Current
205mA
Pin Count
84
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT47H32M16BN-37E:D
Manufacturer:
MICRON
Quantity:
489
Company:
Part Number:
MT47H32M16BN-37E:D
Manufacturer:
MICRON
Quantity:
319
Company:
Part Number:
MT47H32M16BN-37E:D TR
Manufacturer:
Micron Technology Inc
Quantity:
10 000
PDF: 09005aef82f1e6e2
Rev. M 9/08 EN
31. Vil/Vih DDR2 overshoot/undershoot. See AC Overshoot/Undershoot Specification
32. For each input signal—not the group collectively.
33. There are two sets of values listed for command/address:
34. This is applicable to READ cycles only. WRITE cycles generally require additional time
35. READs and WRITEs with auto precharge are allowed to be issued before
36. When a single-bank PRECHARGE command is issued,
37. This parameter has a two clock minimum requirement at any
38. The
39. The minimum internal READ-to-PRECHARGE time. This is the time from which the last 4-
40.
41. The refresh period is 64ms (commercial) or 32ms (industrial and automotive). This equa-
42.
43.
44.
45. The half-clock of
strobe are listed in Table 33 (page 68)–Table 35 (page 69) on Table 33 (page 68),
Table 34 (page 69), and Table 35 (page 69); listed values are already derated for slew
rate variations and converted from baseline values to Vref values.
(page 58).
t
when the slew rate is 1 V/ns. The baseline values,
referenced from the logic trip points.
and Vil(AC) for a falling signal, while
and Vih(DC) for a falling signal. If the command/address slew rate is not equal to 1 V/ns,
then the baseline values must be derated by adding the values from Table 28
(page 61) and Table 29 (page 62).
due to
satisfied because
plies when the PRECHARGE (ALL) command is issued, regardless of the number of banks
open. For 8-bank devices (≥1Gb),
lists
ACTIVATE commands may be issued in a given
still applies.
bit prefetch begins to when the PRECHARGE command can be issued. A 4-bit prefetch is
when the READ command internally latches the READ so that data will output CL later.
This parameter is only applicable when
533 MHz when
(MIN) has to be satisfied as well. The DDR2 SDRAM will automatically delay the internal
PRECHARGE command until
t
ded up to the next integer.
t
programmed to four clocks would have
8 clocks.
tes to an average refresh rate of 7.8125µs (commercial) or 3.9607µs (industrial and
automotive). To ensure all rows of all banks are properly refreshed, 8,192 REFRESH com-
mands must be issued every 64ms (commercial) or 32ms (industrial and automotive). The
JEDEC
allowed.
t
or to CK, CK# being removed in a system RESET condition (see Reset (page 131)).
t
Figure 71 (page 122).
t
clock edges. CKE must remain at the valid input level the entire time it takes to achieve
the three clocks of registration. Thus, after any CKE transition, CKE may not transition
from its valid level during the time period of
must be derated by the amount of half-clock duty cycle error. For example, if the clock
IH
DAL = (nWR) + (
WR parameter stored in the MR9–MR11. For example, -37E at
DELAY is calculated from
ISXR is equal to
CKE (MIN) of three clocks means CKE must be registered on three consecutive positive
a
values (for reference only) are equivalent to the baseline values of
t
t
RP [MIN] +
FAW (MIN) parameter applies to all 8-bank DDR2 devices. No more than four bank-
t
t
RFC MAX of 70,000ns is not required as bursting of AUTO REFRESH commands is
WR during auto precharge.
t
t
RTP = 7.5ns. If
t
CK [AVG] MIN).
t
RP/
IS and is used for CKE setup time during self refresh exit, as shown in
t
t
AOFD’s 2.5
RAS lockout feature is supported in DDR2 SDRAM.
t
CK). Each of these terms, if not already an integer, should be roun-
45
t
IS +
t
CK refers to the application clock period; nWR refers to the
t
RAS (MIN) has been satisfied.
t
CK assumes a 50/50 clock duty cycle. This half-clock value
t
t
RTP/(2 ×
CK +
t
RPA (MIN) =
AC Timing Operating Specifications
Micron Technology, Inc. reserves the right to change products or specifications without notice.
t
t
IH so that CKE registration LOW is guaranteed pri-
t
IH
IS
t
b
t
t
b
RTP/(2 ×
512Mb: x4, x8, x16 DDR2 SDRAM
CK) ≤ 1, then equation AL + BL/2 applies.
DAL = 4 + (15ns/3.75ns) clocks = 4 + (4) clocks =
is referenced from Vih(AC) for a rising signal
is referenced from Vil(DC) for a rising signal
t
IS + 2 ×
t
t
RP (MIN) +
FAW (MIN) period.
t
t
CK) > 1, such as frequencies faster than
IS
b
,
t
RP timing applies.
t
t
CK +
IH
b
t
, are the JEDEC-defined values,
IS
t
CK (AVG) (Table 11 (page 35)
t
a
IH.
,
© 2004 Micron Technology, Inc. All rights reserved.
t
t
CK.
IH
t
CK = 3.75ns with
a
and
t
RRD (MIN) restriction
t
IS
t
IS
t
b
t
RPA timing ap-
RAS (MIN) is
b
,
,
t
IH
t
IH
b
b
. The
at Vref
t
WR
t
RAS
t
IS
a
,