HI5741BIB Intersil, HI5741BIB Datasheet - Page 4

• Manufacturer Part Number: HI5741BIB
• Description: IC DAC 14-BIT 100MSPS 28-SOIC
• Manufacturer: Intersil

Specifications of HI5741BIB

• Settling Time: 20ns
• Number Of Bits: 14
• Data Interface: Parallel
• Number Of Converters: 1
• Voltage Supply Source: Analog and Digital, Dual ±
• Power Dissipation (max): 650mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Electrical Specifications
NOTES:
Spurious Free Dynamic Range to Nyquist
(Note 4)
Multi-Tone Power Ratio
(MTPR)
REFERENCE/CONTROL AMPLIFIER
Internal Reference Voltage, V
Internal Reference Voltage Drift
Internal Reference Output Current Sink/Source
Capability
Internal Reference Load Regulation
Amplifier Input Impedance
Amplifier Large Signal Bandwidth
Amplifier Small Signal Bandwidth
Reference Input Impedance (CTL IN)
Reference Input Multiplying Bandwidth (CTL IN)
DIGITAL INPUTS (D9-D0, CLK, INVERT)
Input Logic High Voltage, V
Input Logic Low Voltage, V
Input Logic Current, I
Input Logic Current, I
Digital Input Capacitance, C
TIMING CHARACTERISTICS
Data Setup Time, t
Data Hold Time, t
Propagation Delay Time, t
CLK Pulse Width, t
POWER SUPPLY CHARACTERISTICS
IV
IV
IV
Power Dissipation
Power Supply Rejection Ratio
2. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board.
3. Gain Error measured as the error in the ratio between the full scale output current and the current through R
4. Parameter guaranteed by design or characterization and not production tested.
5. All devices are 100% tested at +25°C.
6. Dynamic Range must be limited to a 1V swing within the compliance range.
7. In testing MTPR, tone frequencies ranged from 1.95MHz to 3.05MHz. The ratio is measured as the range from peak power to peak distortion in
EEA
EED
CCD
ratio should be 16.
the region of removed tones.
HLD
PARAMETER
SU
PW1
IH
IL
, t
PW2
PD
IL
IH
IN
REF
4
AV
T
A
EE
= +25°C (Continued)
, DV
EE
= -4.94V to -5.46V, V
f
f
f
f
f
f
8 Tones, no Clipping, 110kHz Spacing, 220kHz spacing
between tones 4 and 5, f
(Note 5)
(Note 4)
(Note 4)
I
(Note 4)
4.0V
1.0V
(Note 4)
R
(Note 4)
(Note 5)
(Note 5)
(Note 5)
(Note 5)
(Note 4)
See Figure 1 (Note 4)
See Figure 1 (Note 4)
See Figure 1 (Note 4)
See Figure 1 (Note 4)
(Note 5)
(Note 5)
(Note 5)
(Note 5)
V
CLK
CLK
CLK
CLK
CLK
CLK
REF
L
CC
= 50Ω, 100mV Sine Wave, to -3dB Loss at I
P-P
P-P
= 10 MSPS, f
= 10 MSPS, f
= 25 MSPS, f
= 50 MSPS, f
= 75 MSPS, f
= 100 MSPS, f
±5%, V
= 0 to I
Sine Wave Input, to Slew Rate Limited (Note 4)
Sine Wave Input, to -3dB Loss (Note 4)
REF
EE
HI5741
±5%
= -500µA
TEST CONDITIONS
CC
OUT
OUT
OUT
OUT
OUT
OUT
= +4.75 to +5.25V, V
= 1.023MHz, 5MHz Span
= 2.02MHz, 5MHz Span
= 2.02MHz, 12.5MHz Span
= 5.055MHz, 25MHz Span
= 7.52MHz, 37.5MHz Span
= 10.1MHz, 50MHz Span
CLK
= 20 MSPS (Note 7)
REF
= Internal,
OUT
-1.27
-500
SET
T
MIN
2.0
0.5
1.0
A
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
= -40°C TO +85°C
(typically 1.28mA). Ideally the
HI5741BI
-1.23
TYP
0.25
0.85
100
650
3.0
2.0
4.5
86
85
77
74
73
71
76
50
12
75
42
75
13
3
1
5
5
-
-
-
-
-
-1.17
MAX
+50
400
700
0.8
September 20, 2006
50
95
20
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
FN4071.12
UNITS
µV/°C
µA/V
MHz
MHz
MHz
mW
dBc
dBc
dBc
dBc
dBc
dBc
dBc
MΩ
mA
mA
mA
µA
µV
kΩ
µA
µA
pF
ns
ns
ns
ns
V
V
V