AD7940BRM Analog Devices Inc, AD7940BRM Datasheet - Page 5

• Manufacturer Part Number: AD7940BRM
• Description: IC ADC 14BIT UNIPOLAR 8-MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7940BRM

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Operating Temperature: -40°C ~ 85°C
• Number Of Bits: 14
• Sampling Rate (per Second): 100k
• Number Of Converters: 1
• Power Dissipation (max): 26.4mW
• Voltage Supply Source: Single Supply
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
• Resolution (bits): 14bit
• Input Channel Type: Single Ended
• Supply Voltage Range - Analogue: 2.5V To 5.5V
• Supply Current: 5.2mA
• No. Of Pins: 8
• Sampling Rate: 100kSPS
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: EVAL-AD7940CBZ - BOARD EVALUATION AD7940AD7940-DBRD - BOARD EVAL FOR AD7940 STAMP SPI
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

TIMING SPECIFICATIONS
Sample tested at initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
a voltage level of 1.6 V.
V
Table 3.
Parameter
f
t
t
t
t
t
t
t
t
t
t
t
1
2
3
4
SCLK
CONVERT
QUIET
1
2
3
4
5
6
7
8
POWER-UP
Mark/space ratio for the SCLK input is 40/60 to 60/40.
Measured with the load circuit of
t
back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t
time of the part and is independent of the bus loading.
See the
2
2
3
8
DD
is derived form the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of
1
= 2.50 V to 5.5 V; T
4
Power vs. Throughput Rate
A
= T
Figure 2
MIN
3 V
250
2.5
16 × t
50
10
10
48
120
0.4 t
0.4 t
10
45
1
section.
to T
Limit at T
SCLK
SCLK
SCLK
and defined as the time required for the output to cross 0.8 V or 2.0 V.
MAX
, unless otherwise noted.
MIN
5 V
250
2.5
16 × t
50
10
10
35
80
0.4 t
0.4 t
10
35
1
Figure 2. Load Circuit for Digital Output Timing Specification
, T
SCLK
SCLK
MAX
SCLK
TO OUTPUT
PIN
Unit
kHz min
MHz max
min
ns min
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns max
µs typ
50pF
Rev. 0 | Page 5 of 20
C
L
200µA
200µA
Description
Minimum quiet time required between bus relinquish and start of
next conversion
Minimum CS pulse width
CS to SCLK setup time
Delay from CS until SDATA three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
SCLK high pulse width
SCLK to data valid hold time
SCLK falling edge to SDATA high impedance
Power up time from full power-down
I
I
OL
OH
1.6V
8
, quoted in the timing characteristics is the true bus relinquish
Figure 2.
The measured number is then extrapolated
DD
) and timed from
AD7940