KAD5512P-50Q72 Intersil, KAD5512P-50Q72 Datasheet - Page 23
![IC ADC 12BIT 500MSPS SGL 72-QFN](/photos/6/61/66122/kad5512p-50q72_sml.jpg)
KAD5512P-50Q72
Manufacturer Part Number
KAD5512P-50Q72
Description
IC ADC 12BIT 500MSPS SGL 72-QFN
Manufacturer
Intersil
Series
FemtoCharge™r
Datasheet
1.KAD5512P-50Q72.pdf
(30 pages)
Specifications of KAD5512P-50Q72
Number Of Bits
12
Sampling Rate (per Second)
500M
Data Interface
Serial, SPI™
Number Of Converters
1
Power Dissipation (max)
460mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
72-VFQFN Exposed Pad
For Use With
KDC5512EVAL - DAUGHTER CARD FOR KAD5512KDC5512-50EVAL - DAUGHTER CARD FOR KAD5512
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ADDRESS 0X73: OUTPUT_MODE_A
The output_mode_A register controls the physical output
format of the data, as well as the logical coding. The
KAD5512P-50 can present output data in two physical
formats: LVDS or LVCMOS. Additionally, the drive strength
in LVDS mode can be set high (3mA) or low (2mA). By
default, the tri-level OUTMODE pin selects the mode and
drive level (refer to “Digital Outputs” on page 17). This
functionality can be overridden and controlled through the
SPI, as shown in Table 13.
Data can be coded in three possible formats: two’s
complement, Gray code or offset binary. By default, the
tri-level OUTFMT pin selects the data format (refer to “Data
Format” on page 18). This functionality can be overridden
and controlled through the SPI, as shown in Table 14.
This register is not changed by a Soft Reset.
ADDRESS 0X74: OUTPUT_MODE_B
ADDRESS 0X75: CONFIG_STATUS
Bit 6 DLL Range
Internal clock signals are generated by a delay-locked loop
(DLL), which has a finite operating range. Table 15 shows
the allowable sample rate ranges for the slow and fast
settings.
This bit sets the DLL operating range to fast (default) or
slow.
TABLE 12. CLOCK DIVIDER SELECTION
TABLE 14. OUTPUT FORMAT CONTROL
VALUE
VALUE
TABLE 13. OUTPUT MODE CONTROL
VALUE
001
010
100
000
001
010
100
000
001
010
100
23
OUTPUT FORMAT
Two’s Complement
CLOCK DIVIDER
OUTPUT MODE
Offset Binary
Not Allowed
Divide by 1
Divide by 2
Pin Control
Gray Code
0x72[2:0]
0x93[2:0]
Pin Control
LVDS 2mA
LVDS 3mA
0x93[7:5]
LVCMOS
KAD5512P-50
The output_mode_B and config_status registers are used in
conjunction to enable DDR mode and select the frequency
range of the DLL clock generator. The method of setting
these options is different from the other registers.
The procedure for setting output_mode_B is shown in
Figure 44. Read the contents of output_mode_B and
config_status and XOR them. Then XOR this result with the
desired value for output_mode_B and write that XOR result
to the register.
Device Test
The KAD5512P-50 can produce preset or user defined
patterns on the digital outputs to facilitate in-situ testing. A
static word can be placed on the output bus, or two different
words can alternate. In the alternate mode, the values
defined as Word 1 and Word 2 (as shown in Table 16) are
set on the output bus on alternating clock phases. The test
mode is enabled asynchronously to the sample clock,
therefore several sample clock cycles may elapse before the
data is present on the output bus.
ADDRESS 0XC0: TEST_IO
Bits 7:6 User Test Mode
The four LSBs in this register (Output Test Mode) determine
the test pattern in combination with registers 0xC2 through
0xC5. Refer to “SPI Memory Map” on page 25.
OUTPUT_MODE_B
CONFIG_STATUS
DLL RANGE
These bits set the test mode to static (0x00) or alternate
(0x01) mode. Other values are reserved.
VALUE
FIGURE 39. SETTING OUTPUT_MODE_B REGISTER
Slow
0000
0001
0010
0011
0100
Fast
READ
READ
0x74
0x75
TABLE 16. OUTPUT TEST MODES
Negative Full-Scale
Positive Full-Scale
TABLE 15. DLL RANGES
OUTPUT TEST
Checkerboard
DESIRED
VALUE
0xC0[3:0]
MIN
160
Midscale
80
MODE
Off
MAX
200
500
WORD 1
0xAAAA
0xFFFF
0x8000
0x0000
WRITE TO
October 9, 2009
MSPS
MSPS
WORD 2
UNIT
0x5555
0x74
N/A
N/A
N/A
FN6805.3