DS1687-3IND Maxim Integrated Products, DS1687-3IND Datasheet - Page 8
![IC RTC 3V 64-BIT Y2K 24-EDIP](/photos/6/58/65847/175-24-dip_sml.jpg)
DS1687-3IND
Manufacturer Part Number
DS1687-3IND
Description
IC RTC 3V 64-BIT Y2K 24-EDIP
Manufacturer
Maxim Integrated Products
Type
Clock/Calendar/NVSRAM/Y2Kr
Datasheet
1.DS1685S-5.pdf
(34 pages)
Specifications of DS1687-3IND
Memory Size
242B
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.7 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
24-DIP (600 mil) Module
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS1687-3IND
Manufacturer:
MAXIM
Quantity:
2 450
Company:
Part Number:
DS1687-3IND+
Manufacturer:
LT
Quantity:
665
POWER-DOWN/POWER-UP CONSIDERATIONS
The RTC function continues to operate, and all of the RAM, time, calendar, and alarm memory locations remain
nonvolatile regardless of the level of the V
and maximum limits whenever V
point), the device becomes accessible after t
chain is not in reset (Register A). This time period allows the system to stabilize after power is applied. If the
oscillator is not enabled, the oscillator enable bit will be enabled on power up, and the device becomes immediately
accessible.
The DS1685/DS1687 is available in either a 3V or a 5V device.
The 5V device is fully accessible and data can be written and read only when V
falls below V
input voltage. As V
lithium battery connected either to the V
The 3V device is fully accessible and data can be written or read only when V
falls below V
V
V
V
When V
exception of the KS, PWR, and SQW pins, all inputs are ignored and all outputs are in a high-impedance state.
TIME, CALENDAR, AND ALARM LOCATIONS
The time and calendar information is obtained by reading the appropriate register bytes shown in Table 2. The
time, calendar, and alarm are set or initialized by writing the appropriate register bytes. The contents of the time,
calendar, and alarm registers can be either binary or binary coded decimal (BCD) format. Table 2 shows the binary
and BCD formats of the 10 time, calendar, and alarm locations that reside in both bank 0 and in bank 1, plus the
two extended registers that reside in bank 1 only (bank 0 and bank 1 switching are explained later in this text).
Before writing the internal time, calendar, and alarm registers, the SET bit in Register B should be written to a logic
1 to prevent updates from occurring while access is being attempted. Also at this time, the data format (binary or
BCD) should be set by the data mode bit (DM) of Register B. All time, calendar, and alarm registers must use the
same data mode. Invalid time and date entries will result in undefined operation. The set bit in Register B should
be cleared after the data mode bit has been written to allow the RTC to update the time and calendar bytes. If the
oscillator is running, the time and date registers will update 500ms after the countdown chain is enabled.
Once initialized, the RTC makes all updates in the selected mode. The data mode cannot be changed without
reinitializing the 10 data bytes. The 24/12 bit cannot be changed without reinitializing the hour locations. When the
12-hour format is selected, the high order bit of the hours byte represents PM when it is a logic 1. The time,
calendar, and alarm bytes are always accessible because they are double buffered. Once per second the 10 bytes
are advanced by one second and checked for an alarm condition
If a read of the time and calendar data occurs during an update, a problem exists where seconds, minutes, hours,
etc., might not correlate. The probability of reading incorrect time and calendar data is low. Several methods of
avoiding any possible incorrect time and calendar reads are covered later.
The three time alarm bytes can be used in two ways. First, when the alarm time is written in the appropriate hours,
minutes, and seconds alarm locations, the alarm interrupt is initiated at the specified time each day if the alarm
enable bit is high.
The second use condition is to insert a “don’t care” state in one or more of the three time-alarm bytes. The “don’t
care” code is any hexadecimal value from C0 to FF. The two most significant bits of each byte set the “don’t care”
condition when at logic 1. An alarm is generated each hour when the “don’t care” bits are set in the hours byte.
Similarly, an alarm is generated every minute with “don’t care” codes in the hours and minute alarm bytes. The
CC
BAUX
BAUX
to the backup supply (the greater of V
, the power supply is switched from V
.
CC
falls below V
PF
PF
, reads and writes are inhibited. If V
, read and writes are inhibited. However, the timekeeping function continues unaffected by the lower
CC
falls below the greater of V
PF
, the device inhibits access by internally disabling the CS input. With the possible
CC
is not at a valid level. When V
BAT
BAT
CC
pin or V
CC
REC
input.
and V
to the backup supply when V
, provided that the oscillator is running and the oscillator countdown
BAT
PF
BAUX
BAUX
.
is less than V
At least one back up supply must remain within the minimum
and V
8 of 34
pin.
) when V
BAUX
, the RAM and timekeeper are switched over to a
CC
BAT
drops below V
CC
and V
is applied and exceeds V
DS1685/DS1687 3V/5V Real-Time Clocks
BAUX
CC
, the power supply is switched from
drops below the larger of V
CC
CC
PF
is greater than 2.7V. When V
is greater than 4.5V. When V
. If V
PF
is greater than V
PF
(power-fail trip
BAT
BAT
and
and
CC
CC