1-353293-8 TE Connectivity, 1-353293-8 Datasheet
![MINI CT MT REC ASSY 18P GRAY](/photos/41/47/414783/pr353293_sml.jpg)
1-353293-8
Specifications of 1-353293-8
Available stocks
Related parts for 1-353293-8
1-353293-8 Summary of contents
Page 1
... Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality assurance provisions of AMP Mini Common Termination (CT) Connector 1.5mm Pitch (MT Type). Applicable product description and part numbers are as shown in Fig.1. 2. Applicable Documents: The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence ...
Page 2
... Requirements: 3.1 Design and Construction: Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2 Materials: A. Receptacle Assembly Contact: Pre tin plated Phosphor Bronze (0.8µm min.thick pre tin plated over 0.5µm min.thick copper underplate) Housing : 66 Nylon G ...
Page 3
... Applicable Panel Thickness 0.8~ 1.6mm (To be used for post header assembly relay) 3.7 Performance Requirements and Test Descriptions : The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig ...
Page 4
... Fig.4. 500 VAC for 1 minute. Test between adjacent circuits of mated connectors. MIL STD 202 TEST METHOD 301 Impressed voltage 500 VDC for 1 minute. Test between adjacent circuits of mated connectors. MIL STD 202 TEST METHOD 302 CONDITION A Contacts series-wired,apply test current of loaded rating ...
Page 5
... PAGE Document No Procedures Apply a pull-off load to terminated wire of contact secured on the tester, Operation Speed : 50 mm/min. The load is applied in (1) the axial and (2) the traverse directions as specified. Fig.5 Measure post retention force. Operation Speed : 50 mm/min. Fig.6 Apply an axial pull-off load to crimped wire. ...
Page 6
... Accelerated Velocity : 2 490 m Waveform: halfsine shock pulse Duration : 11 msec. Number of Drops : 3 drops each to normal and reversed directions and Z axes, totally 18 drops applied. MIL-STD-202 TEST METHOD 213 CONDITION A IEC 68-2-27 Mounting : Fig. 9 Under 10000 cycles of repeated hammering shocks of the condition as shown Fig.10,with the test current of 1mA at 10VDC applied to the circuit as shown in Fig ...
Page 7
... Cold shock - 10 °C performed 20 mΩ Max. (Final) IEC 68-2-38 20 mΩ Max. (Final) Subject mated 35 ± 2 ℃ connectors to 5 ± salt concentration for 48 hours : Aften test,ninse the samples with waten and recondition the room temperature for hour. IEC 68-2-11 Fig ...
Page 8
... Max. (Final) Mated connector - 40 ± 3 °C, 500 hours IEC 68-2-1 20 mΩ Max. (Final) Mated connector SO2 Gas : 10 ± 3 ppm R.H. 35 ± 2 °C, 240 hours 20 mΩ Max. (Final) Mated connector H2S Gas : 3 ppm,40 ± 3 ℃ R.H.、 240 hours 20 mΩ ...
Page 9
... Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,6 1,3 1,3 1,3 1,3 1,3 1,3 1,3 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2 Fig.3 (To be continued) PAGE Document No. ...
Page 10
... Industrial H S Gas 2 Industrial Ammonia Gas Resistance to Solvent (a) Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2 ...
Page 11
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 4 Fig. 5 Fig. 6 PAGE Document No. 108-5525 REV LOC A ES ...
Page 12
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 7 Fig. 8 PAGE Document No. 108-5525 REV LOC A ES ...
Page 13
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 10 PAGE Document No. 108-5525 REV LOC A ES ...
Page 14
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 11 PAGE Document No. 108-5525 REV LOC A ES ...
Page 15
... Note : To be applied same specification to post header relay panel mount type by measurement on opposite lock side. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Unmating Force N (kgf) min. 2.99 ) 4.508 ( 0.46 3 ...
Page 16
... The applicable product descriptions and part numbers are as shown in Fig.1. Product Part No. ×-353293-× ×-353297-× ×-84742-× ×-353300-× ×-353301-× ×-353520-× ×-353521-× ×-353523-× ×-353524-× ×-353303-× ...
Page 17
... Double Row Post Header Assembly (V) SMT Type With Boss 22~ 40 Pos.(Only Even Number Pos.) Double Row Post Header Assembly Panel Mount Type 22~ 40 Pos. Double Row Post Header Assembly (H) DIP Type 22~ 40 Pos.(Only Even Number Pos.) Fig. 1(End) PAGE Document No. REV 108-5525 LOC A ES ...