E2Q2-N15F1-51 Omron, E2Q2-N15F1-51 Datasheet - Page 8
![Proximity Sensors INDUCTIVE PNP-NO](/photos/33/12/331221/e2q2f_sml.jpg)
E2Q2-N15F1-51
Manufacturer Part Number
E2Q2-N15F1-51
Description
Proximity Sensors INDUCTIVE PNP-NO
Manufacturer
Omron
Series
E2Q2r
Type
Inductive Proximity Sensorr
Datasheet
1.E2Q2-N15F1-51.pdf
(8 pages)
Specifications of E2Q2-N15F1-51
Proximity Sensor Type
Inductive
Proximity Sensor Sensing Distance
15mm
Proximity Sensor Sensing Distance Range
15 to 50mm
Proximity Sensor Switching Mode
NO
Operating Temp Range
-25C to 70C
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
10V
Operating Supply Voltage (typ)
12/15/18/24V
Operating Supply Voltage (max)
30V
Pin Count
3
Output Type
PNP
Maximum Operating Temperature
+ 70 C
Supply Voltage
30 V
Operating Supply Voltage
10 V to 60 V
Sensing Distance
15 mm
Minimum Operating Temperature
- 25 C
Features
Sensing face easily adjusts to one of five directions
Sensor Type
Inductive
Sensing Object
Metallic
Response Frequency
10Hz
Material - Body
PBT Plastic
Shielding
Shielded
Voltage - Supply
10 V ~ 30 V
Terminal Type
1/2" NPT
Package / Case
Cylinder, Threaded
Lead Free Status / RoHS Status
Supplier Unconfirmed
Precautions
Power supply
Do not impose an excessive voltage on the E2Q2, otherwise it
may explode or burn.
Do not impose AC voltage on any E2Q2 DC model, otherwise it
may explode or burn.
Do not connect the AC types without load to the power supply.
The sensor will be damaged.
J INSTALLATION
Power Reset Time
The Proximity Sensor is ready to operate within 300 ms after
power is supplied. If power supplies are connected to the
Proximity Sensor and load respectively, be sure to supply power
to the Proximity Sensor before supplying power to the load.
Power OFF
The Proximity Sensor may output a pulse signal when it is turned
off. Therefore, it is recommended to turn off the load before
turning off the Proximity Sensor.
E2Q2
Cat. No. CEDSAX4
1-800-55-OMRON
OMRON ELECTRONICS LLC
One East Commerce Drive
Schaumburg, IL 60173
Sensor
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
Sensor
Brown
Blue
!
Black
CAUTION
Load
R
11/01
Incorrect
OMRON ON- -LINE
Global -- http://www.omron.com
USA -- http://www.omron.com/oei
Canada -- http://www.omron.com/oci
Specifications subject to change without notice.
Power Supply Transformer
When using a DC power supply, make sure that the DC power
supply has an insulated transformer. Do not use a DC power
supply with an auto- - transformer.
Sensing Object
Metal coating: The sensing distance of the proximity sensor will
vary with the metal coating on sensing objects.
J WIRING
High- - Tension Lines
Wiring through Metal Conduit
If there is a power or high- - tension line near the cable of the
Proximity Sensor, wire the cable through an independent metal
conduit to prevent against Proximity Sensor damage or
malfunctioning.
J MOUNTING
The Proximity Sensor must not be subjected to excessive shock
with a hammer when it is installed, otherwise the Proximity
Sensor may be damaged or lose its water resistance.
J ENVIRONMENT
Water Resistance
Do not use the proximity sensor underwater, outdoors or in the
rain.
Operating Environment
Be sure to use the Proximity Sensor with operating ambient
temperature range and do not use the Proximity Sensor outdoors
so that its reliability and life expectancy can be maintained.
Although the Proximity Sensor is water resistant, a cover to
protect he proximity sensor from water or soluble machining oil is
recommended so that its reliability and life expectancy can be
maintained. Do not use the Proximity Sensor in an environment
with chemical gas (e.g., strong alkaline or acid gases including
nitric, chromic, and concentrated sulfuric acid gases).
OMRON CANADA, INC.
416-286-6465
885 Milner Avenue
Scarborough, Ontario M1B 5V8
Printed in U.S.A.
E2Q2