KSZ8721SL A4 Micrel Inc, KSZ8721SL A4 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/434/micrel_inc_sml.jpg)
KSZ8721SL A4
Manufacturer Part Number
KSZ8721SL A4
Description
Manufacturer
Micrel Inc
Datasheet
1.KSZ8721SL_A4.pdf
(34 pages)
Specifications of KSZ8721SL A4
Lead Free Status / RoHS Status
Compliant
KS8721BL/SL
Power Management
The KS8721BL/SL offers the following modes for power management:
100BT FX Mode
Please contact your local field application engineer (FAE) for a reference schematic on fiber connection.
100BT FX mode is activated when FXSD/FXEN is higher than 0.6V (this pin has a default pull down). Under this mode, the
auto-negotiation and auto-MDI-X features are disabled.
In fiber operation, the FXSD pin should connect to the signal detect (SD) output of the fiber module. The internal threshold
of FXSD is around 1/2 V
is summarized in the following table:
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
Far End Fault (FEF), repetition of a special pattern which consists of 84-one and 1-zero, is generated under “FX mode with
no signal detected.” The purpose of FEF is to notify the sender of a faulty link. When receiving an FEF, the LINK will go down
to indicate a fault, even with fiber signal detected. The transmitter is not affected by receiving an FEF and still sends out its
normal transmit pattern from MAC. FEF can be disabled by strapping pin 27 low. Refer to the “Strapping Options” section.
Media Converter Operation
The KS8721BL/SL is capable of performing media conversion with two parts in a back-to-back RMII loop-back mode as
indicated in the diagram. Both parts are in RMII mode and with RMII BTB asserted (pins 21 and 22 strapped high). One part
is operating in TX mode and the other is operating in FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-negotiation on the TX side prohibits 10BASE-T link-up. Additional options can be implemented
under this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2
and TXD2 pins need to be connected via inverter. When TXD2 pin is high in both the copper and fiber operation, it is disabled
transmit. Meanwhile, the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected.
TXD3 should be tied low and RXD3 let float. Please contact your Micrel FAE for a media converter reference design.
M9999-022105
FXSD/FXEN
Less than 0.6V
Less than 1.25V,
but greater than 0.6V
Greater than 1.25
• Power-Down Mode: This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# low.
• Power-Saving Mode: This mode can be disabled by writing to Register 1fh.10. The KS8721BL/SL turns off everything
except for the Energy Detect and PLL circuits when the cable is not installed. In other words, the KS8721BL/SL
shuts down most of the internal circuits to save power if there is no link. Power-saving mode is in the most effec-
tive state when auto-negotiation mode is enabled.
DD
Condition
100TX mode
FX mode
No signal detected
FEF generated
FX mode
Signal detected
±50mV (1.25V ±0.05V). Above this level, the fiber signal is considered detected. The operation
To the SD pin of the
Fiber Module
Table 1. 100BT FX Mode
Figure 3. Fiber Module
Rx +/-
Tx +/-
FR x
FTx
KS8721BL/SL
KS8721BL/SL
Pin
34
(Fiber Mode)
16
Ref_CLK
Ref_CLK
21 22
TxC/
TxC/
21 22
Pin
Pin
RxD
TxD
TxD
RxD
V
V
CC
CC
50MHz
OSC
February 2005
Micrel