CLAMP04 Cirrus Logic Inc, CLAMP04 Datasheet

CLAMP04

Manufacturer Part Number

CLAMP04

Description

CLAMP TO220 USE WITH HS29

Manufacturer

Cirrus Logic Inc

Series

HSr

Datasheet

1.CLAMP04.pdf (1 pages)

Specifications of CLAMP04

Accessory Type

Clamp

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

For Use With/related Products

HS29

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Other names

598-1482
CLAMP04

Current page: 1 of 1
Download datasheet (165Kb)

� � � � � � � � � � � � � � �

EVALUATION KIT

possible with the EK33 PC board. Mounting holes are provided

and the provision for standard banana jacks simpliﬁes con-

nection and testing. Components are labeled on both sides

of the board for ease in probing. This kit is not suitable for

PA75CC or PA75CD. A multitude of circuit conﬁgurations are

possible, so only several component locations have speciﬁc

functions and will usually be necessary.

PARTS LIST

Part #

Eval33

Clamp04

MS11

TW14

HS29

HEATSINKS

HS29 2.7°C/W

drilled and deburred. Requirements for the potential heatsink

or chassis member are ﬂatness of 2 mils per inch in an area

large enough to ﬁt the package.

CAGE JACKS

MS11

APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com

This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. All speciﬁcations are subject to change without notice.

Fast, easy breadboarding of circuits using the PA75CX are

Many heatsinks can be used with this ampliﬁer if a holes is

Description

Evaluation Board

Clamp for HS29

Pin Recp., Strip of 30

Thermal Washer TO-220 10/Pack

Heat Sink, 2.7 DEG/W

� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

��

Quantity

jacks. The strip can easily be cut to any desired number of

cage jacks. These are mounted directly in a print circuit board.

After soldering, the carrier is pulled off the cage jacks. Use

a spacer between the PCB and the heatsink to avoid short

circuits.

THERMAL WASHER

TW14

NOTES:

1. Base material is aluminum, 0.002” thick. Do not allow the

2. For optimum thermal transfer, avoid abrasive handling

3. The dry thermal compound will ﬂow ﬁlling header to heatsink

4. Do not store unused thermal washers above 40°C.

5. A new washer must be used for each mounting.

6. Part number TW14 consists of a package of 10 washers.

7. Thermal resistance is 0.17°C/W.mal compound with which

Part number MS11 consists of a carrier strip of 30 cage

washer to touch pins of the ampliﬁer.

of washers which can damage their 0.5mil thick layer of

thermal compound with which each side is coated.

voids as soon as the material reached 60°C.

each side is coated.

Related parts for CLAMP04

Related keywords

clamp
CLAMP04 datasheet
CLAMP04 data sheet
CLAMP04 pdf datasheet
CLAMP04 component
CLAMP04 part
CLAMP04 distributor
CLAMP04 RoHS
CLAMP04 datasheet download