FLUKE-700HTP-1 Fluke, FLUKE-700HTP-1 Datasheet
FLUKE-700HTP-1
Manufacturer Part Number
FLUKE-700HTP-1
Description
HYDRAULIC TEST PUMP, 10,000 PSI
Manufacturer
Fluke
Datasheet
1.FLUKE-700HTP-1.pdf
(2 pages)
Specifications of FLUKE-700HTP-1
Operating Pressure Max
10000psi
Size
9.5 X 6.1 X 2.6"
Fluid Type
Water / Hydraulic Oil
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na
4.
5.
6.
7.
8.
9.
10. Prime pump as described under “Priming the Pump”.
11. Shorten handle-stroke length to reduce pumping force.
12. Compress the handles to apply incrementally higher
13. For fine pressure adjustment, use the fine adjustment
Priming the Pump
To prime the pump:
1.
2.
3.
4.
5.
6.
Replacement Parts
Rebuild Kit, Fluke PN 2812606
Hydraulic Fluid Reservoir Rebuild Kit, Fluke PN 2844341
Handle Assembly Rebuild Kit, Fluke PN 2844352
This Fluke product will be free from defects in material and workmanship for
one year from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage from accident, neglect, misuse, alteration,
contamination, or abnormal conditions of operation or handling. Resellers are
not authorized to extend any other warranty on Fluke’s behalf. To obtain
service during the warranty period, contact your nearest Fluke authorized
service center to obtain return authorization information, then send the product
to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may not apply to you.
11/99
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Connect the input of the pressure instrument under test
to the test pressure port (item B).
Unscrew the pressure release knob (item I) to vent
pressure from the pump.
Zero the pressure module. The zeroing procedure
depends on which pressure module and calibrator you
are using.
Turn the fine adjustment knob (item D) to mid-range.
Tighten the pressure release knob finger tight.
Set the handle stroke length to maximum.
pressure.
knob.
Connect the pressure module and calibration hose
(Fluke HTH or equivalent) as shown in the drawing. Be
sure to use several wraps of Teflon tape on all threaded
connections to insure a proper seal.
Fill the reservoir approximately 2/3 with either de-ionized
water or mineral oil.
Before connecting the other end of the calibration hose
to the device under test, raise the open end of the hose
to a level above the fluid in the reservoir.
Close the pressure release knob and begin pumping the
HTP until fluid begins to come out of the hose. Note that
depending on the volume of the hose this may take 50 or
more strokes.
Once the fluid starts to flow out of the hose, connect to
the unit under test.
When testing is complete, disconnect the hose from the
unit under test. If using the Fluke HTH hose, place the
plastic sealing cap back over the exposed end of the
hose to help retain the fluid until the pump is used again.
Retaining the fluid in the hose will greatly reduce the
number of strokes required to re-prime the pump.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
Pressure may rise rapidly if the
pressurized volume is small.
WCaution
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
PN 2811836
April 2007
©2007 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
Introduction
The Fluke-700HTP-1 Hydraulic Test Pump (hereafter called
the pump) is a portable source of high pressure. The pump
has the following specifications:
•
•
•
•
•
Box Contents
•
•
•
•
Contacting Fluke
To contact Fluke or for service, call one of the following
telephone numbers:
USA: 1-888-44-FLUKE (1-888-443-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Or, visit Fluke's Web site at www.fluke.com.
Maximum pressure: 690 bar (10,000 psi)
Hydraulic media: distilled water or mineral based
hydraulic oil
Wetted materials: 303 stainless steel, aluminum,
polyurethane, PTFE, nitrile, and nylon
Weight: 1.29 lb (.58 kg)
Dimensions: length 9.5 in (241 mm), width 6.1 in
(155 mm), depth 2.6 in (66 mm)
Model 700HTP-1 Hydraulic Test Pump with 1/4 in NPT
tee installed
(2) 1/4 in NPT male to 1/4 in BSP female adapter
1/4 in NPT male to 1/4 in NPT male fitting
Instruction Sheet
Fluke-700HTP-1
Hydraulic Test Pump
Instruction Sheet
®
Related parts for FLUKE-700HTP-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT PROBE LIGHT
Manufacturer:
Fluke Electronics
Datasheet:
Part Number:
Description:
Watertight Hard Storage Case With Rollers
Manufacturer:
Fluke
Datasheet:
Part Number:
Description:
Dry-Well, Handheld Hi-Temp, Block A
Manufacturer:
HART SCIENTIFIC FLUKE
Part Number:
Description:
(PM5415 / PM5418) Color TV Pattern Generator
Manufacturer:
Fluke
Datasheet:
FLUKE-700HTP-1 Summary of contents
Page 1
... The Netherlands 11/99 Fluke-700HTP-1 Hydraulic Test Pump Instruction Sheet Introduction The Fluke-700HTP-1 Hydraulic Test Pump (hereafter called the pump portable source of high pressure. The pump has the following specifications: • Maximum pressure: 690 bar (10,000 psi) • Hydraulic media: distilled water or mineral based hydraulic oil • ...
Page 2
... Fluke 700PRV-1 Pressure Relief Valve on the pump. Attach a 700 Series Pressure Module (hereafter called "pressure module") to the master instrument port A for all modules except the 700P High Pressure Modules ...