78Q8430-100CGTR/F Maxim Integrated Products, 78Q8430-100CGTR/F Datasheet - Page 48
78Q8430-100CGTR/F
Manufacturer Part Number
78Q8430-100CGTR/F
Description
Telecom ICs 10/100MAC+PHY MULTI MEDIA OFFLOAD CNTRLR
Manufacturer
Maxim Integrated Products
Datasheet
1.78Q8430-ARM9-EVM.pdf
(88 pages)
- Current page: 48 of 88
- Download datasheet (2Mb)
78Q8430 Data Sheet
DS_8430_001
6.11.1.5 Signal Quality Error
In 10 Mbps mode, the MAC checks for a “heartbeat” at the end of a transmitted packet. This is a short
Collision signal within the first 40 bit times after end of transmission. Signal Quality Error sets the No
Heart Beat bit in the Transmit Packet Status Register (TPSR).
6.11.1.6 Deferral
In half duplex mode, during any attempt to send a packet, the MAC may have to defer the transmission
because of a pre-occupied network. This is not an error, but is used as a network activity indicator, but
only when collisions do not occur. Deferral sets the Deferral bit of the Transmit Packet Status Register
(TPSR).
6.11.1.7 Excessive Deferral
In half duplex operation, the MAC will defer transmission of frames when there is network activity. If the
deferral time is longer than two maximum sized frame times (2.4288 ms for 10-Mbps operation or 0.24288
ms for 100-Mbps operation) then the Excessive Deferral bit of the Transmit Packet Status Register
(TPSR) is set. If the Tx Enable bit of the MCR Register (MCR) is clear, then the transmission is aborted.
Excessive deferral indicates a possible network problem.
6.11.2 MAC Receive Errors
6.11.2.1 Alignment Error
At the end of reception, the MAC receive block checks that the incoming packet has been correctly
framed on an 8-bit boundary. If it is not and the CRC is invalid, data has been disrupted through the
network and the MAC receive block reports an alignment error. A CRC error is also reported. The
Dangling Byte bit and the CRC bit are set in the Receive Packet Status Register (RPSR).
6.11.2.2 CRC Error
At the end of reception, the MAC receive block checks the CRC for validity and reports a CRC error if it is
invalid.
6.11.2.3 Overflow Error
During reception, incoming data is put into the MAC receive FIFO before it is transferred to the QUE
receive controller. If the MAC receive FIFO fills up because of excessive system latency or other
reasons, the MAC receive block sets the Overflow Error of the Receive Packet Status Register (RPSR)
and the remaining frame is dropped.
6.11.2.4 Length Error
The MAC receive block checks the length of the incoming packet at the end of reception based on the
value of the Len/Type field of the frame. If the length is specified in the Len/Type field and the frame is
longer than the maximum frame size of 1518 bytes, (1522 for VLAN tagged packets), the MAC receive
block reports a length error, unless long frame mode is enabled. The MAC will also flag as an error a
MAC control frame that is not exactly 64 bytes in length.
6.11.2.5 MII Error
The PHY informs the MAC if it detects a media error (such as coding violation) by asserting RX_ER.
When the PHY asserts RX_ER, the MAC sets the MII error bit in the Receive Packet Status Register
(RPSR).
48
Rev. 1.2
Related parts for 78Q8430-100CGTR/F
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Telecom ICs 10/100MAC+PHY MULTI MEDIA OFFLOAD CNTRLR
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Telecom ICs 10/100MAC+PHY MULTI MEDIA OFFLOAD CNTRLR
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
10/100 Ethernet Mac And Phy
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
IC LAN MEDIA ACCESS CTLR 100LQFP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
EVALUATION MODULE 78Q8430 ARM9
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC LAN MEDIA ACCESS CTLR 100LQFP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC, ETHERNET TXRX, IEEE 802.3, LQFP-100
Manufacturer:
TERIDIAN
Datasheet:
Part Number:
Description:
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products