DRT2-OD32B-1 Omron, DRT2-OD32B-1 Datasheet - Page 50
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
DRT2-OD32B-1
Manufacturer Part Number
DRT2-OD32B-1
Description
32 Out Horiz MIL Connector PNP
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32B-1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 50 of 600
- Download datasheet (13Mb)
Creating and Registering
Scan Lists
2-5
2-5-1
2-5-2
Checking Operation
Checking Operation
Indicator Status
Reading and Writing Data
Use the following procedure to create, register, and enable the scan lists.
In the following example, n = 1500 + (25 × unit number).
Clearing and Creating Scan Lists
Switch the operating mode switch to PROGRAM mode.
Enable the Master Unit functions. Set the Master Unit function enable switch
(bit 06 of word n) from OFF to ON.
Clear the scan lists. Set the scan list clear switch (bit 01 of word n) from OFF
to ON.
Select the fixed allocation areas 1 to 3. Set the Master Unit's setting switch for
fixed allocation areas 1 to 3 (bit 00 of word n) from OFF to ON.
Enable the scan lists. Set the scan list enable switch (bit 00 of word n) from
OFF to ON.
Switch the operating mode switch to RUN or MONITOR mode.
Checking the Normal Slave Table
Monitor the normal Slave table and check that the corresponding bits are ON.
In the normal Slave table, the corresponding bits will turn ON for the nodes
that are communicating normally.
Use the procedures provided here to check that I/O communications are oper-
ating normally.
I/O communications are operating normally if the MS and NS indicators for all
nodes are lit green, and the 7-segment indicator on the front panel of the Mas-
ter Unit is displaying the node address of the Master Unit as shown in the fol-
lowing diagram (when the Master Unit's node address is 00), and the scan list
is enabled.
Connect the Peripheral Device for the PLC to the Master Unit, write the Mas-
ter Unit's OUT Area and read the IN Area, and check that the data are the
same in the Slaves.
Refer to the operation manual for the Master Unit for details on OUT Area and
IN Area addresses and how to allocate Slave I/O.
Master Unit 7-segment
Display
OFF: Operating as a Slave.
OFF: Scan list enabled.
Master Unit node address 00
Display switches between error code and error
node address when an error occurs.
Section 2-5
29
Related parts for DRT2-OD32B-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DRT2-MD16S-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
![DRT2-OD16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-MD16S](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
![DRT2-OD08](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: