DRT2-OD32B-1 Omron, DRT2-OD32B-1 Datasheet - Page 330
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
DRT2-OD32B-1
Manufacturer Part Number
DRT2-OD32B-1
Description
32 Out Horiz MIL Connector PNP
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32B-1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 330 of 600
- Download datasheet (13Mb)
Baud Rate Setting
7-2-3
Using DIN Track
Connecting End Plates
Mounting Direction
Common Procedures
Mounting in Control Panels
Note Any node address within the setting range can be used as long as it is not
Note Always attach End Plates to both ends of Slaves connected to the DIN Track.
Note The input accuracy of a DRT2-TS04T is slightly less accurate if mounted ver-
2. The following window will be displayed. Enter the node address.
3. Click the OK Button.
already set for another node. Setting the same node address for more than
one node will cause a node address duplication error and communications will
not start.
The baud rate of the system is determined by the baud rate set for the Master
Unit (automatic detection). Setting the baud rate for each Unit is not required.
An Analog Slave can be mounted in a control panel using the following
method.
Mount the back of the Slave to a 35-mm DIN Track. To mount the Slave, pull
down on the mounting hook on the back of the Unit with a screwdriver, latch
the DIN Track onto the back of the Slave, and then secure the Slave to the
DIN Track. Secure the Slaves by mounting End Plates on both sides of them.
Hook the bottom of the End Plates onto the DIN Track, as shown at (1) in the
following diagram, then hook the top of the End Plates as shown at (2).
Unless specific restrictions are given for the Slave, it can be mounted in any of
the following six directions. The input accuracy of the DRT2-TS04T depends
on the mounting method in some cases (see note).
tically or facing down (mounting direction 3, 4, or 6 below) when the
DRT2-TS04T is used to replace another Temperature Input Terminal and the
existing Terminal Block is left in place. For details, refer to the Performance
End plate
2
1
Section 7-2
309
Related parts for DRT2-OD32B-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DRT2-MD16S-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
![DRT2-OD16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-MD16S](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
![DRT2-OD08](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: