ADE7758ARWZRL Analog Devices Inc, ADE7758ARWZRL Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADE7758ARWZRL
Manufacturer Part Number
ADE7758ARWZRL
Description
IC,Power Metering,SOP,24PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.ADE7758ARWZ.pdf
(72 pages)
Specifications of ADE7758ARWZRL
Input Impedance
380 KOhm
Measurement Error
0.1%
Voltage - I/o High
2.4V
Voltage - I/o Low
0.8V
Current - Supply
8mA
Voltage - Supply
4.75 V ~ 5.25 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (0.300", 7.50mm Width)
Meter Type
3 Phase
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADE7758ARWZRL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Current RMS Offset Compensation
The ADE7758 incorporates a current rms offset compensation
register for each phase (AIRMSOS, BIRMSOS, and CIRMSOS).
These are 12-bit signed registers that can be used to remove
offsets in the current rms calculations. An offset can exist in the
rms calculation due to input noises that are integrated in the dc
component of I
the current rms calculation is 1,914,753d with full-scale ac
inputs (60 Hz), one LSB of the current rms offset represents
0.94% of the measurement error at 60 dB down from full scale.
The IRMS measurement is undefined at zero input. Calibration
of the offset should be done at low current and values at zero
input should be ignored. For details on how to calibrate the
current rms measurement, see the Calibration section.
where IRMS
Table 7. Approximate IRMS Register Values
Frequency (Hz)
50
60
Voltage Channel RMS Calculation
Figure 63 shows the details of the signal path for the rms
estimation on Phase A of the voltage channel. This voltage rms
estimation is done in the ADE7758 using the mean absolute
value calculation, as shown in Figure 63.The voltage channel
rms value is processed from the waveform samples after the
low-pass filter LPF1. The output of the voltage channel ADC
can be scaled by ±50% by changing VRMSGAIN[11:0] registers
to perform an overall rms voltage calibration. The VRMSGAIN
registers scale the rms calculations as well as the apparent
energy calculation because apparent power is the product of the
voltage and current rms values. The voltage rms values are
stored in 24-bit registers (AVRMS, BVRMS, and CVRMS). One
LSB of a voltage waveform sample is approximately equivalent to
256 LSBs of the voltage rms register. The update rate of the
voltage rms measurement is CLKIN/12.
With the specified full-scale ac analog input signal of 0.5 V, the
LPF1 produces an output code that is approximately 63% of its
full-scale value, that is, ±9,372d, at 60 Hz (see the Voltage
Channel ADC section). The equivalent rms value of a full-scale
ac signal is approximately 1,639,101 (0x1902BD) in the VRMS
register.
The accuracy of the VRMS measurement is typically 0.5% error
from the full-scale input down to 1/20 of the full-scale input.
Additionally, this measurement has a bandwidth of 260 Hz. It is
recommended to read the rms registers synchronous to the
voltage zero crossings to ensure stability. The IRQ can be used
to indicate when a zero crossing has occurred (see the
Interrupts section).
IRMS
=
0
is the rms measurement without offset correction.
IRMS
2
(t). Assuming that the maximum value from
0
2
1,921,472
1,914,752
Integrator Off (d)
+
16384
×
IRMSOS
Integrator On (d)
2,489,581
2,067,210
Rev. D | Page 29 of 72
(9)
Table 8 shows the settling time for the VRMS measurement,
which is the time it takes for the rms register to reflect the value
at the input to the voltage channel.
Table 8. Settling Time for VRMS Measurement
63%
100 ms
Voltage RMS Offset Compensation
The ADE7758 incorporates a voltage rms offset compensation
for each phase (AVRMSOS, BVRMSOS, and CVRMSOS).
These are 12-bit signed registers that can be used to remove
offsets in the voltage rms calculations. An offset can exist in the
rms calculation due to input noises and offsets in the input
samples. It should be noted that the offset calibration does not
allow the contents of the VRMS registers to be maintained at 0
when no voltage is applied. This is caused by noise in the
voltage rms calculation, which limits the usable range between
full scale and 1/50th of full scale. One LSB of the voltage rms
offset is equivalent to 64 LSBs of the voltage rms register.
Assuming that the maximum value from the voltage rms
calculation is 1,639,101d with full-scale ac inputs, then 1 LSB of
the voltage rms offset represents 0.042% of the measurement
error at 1/10 of full scale.
where VRMS
correction.
Table 9. Approximate VRMS Register Values
Frequency (Hz)
50
60
VAN
VOLTAGE SIGNAL–V(t)
VRMS = VRMS
AVRMSGAIN[11:0]
GAIN
0.5
0
is the rms measurement without the offset
Figure 63. Voltage RMS Signal Processing
LPF1
0
+ VRMSOS × 64
50Hz
60Hz
0xD8B8
|
0xD869
0x2797
0x2748
X
|
0x0
0x0
LPF3
100%
960 ms
LPF OUTPUT
WORD RANGE
LPF OUTPUT
WORD RANGE
SGN 2
Value (d)
1,678,210
1,665,118
16
2
VRMSOS[11:0]
15
50Hz
60Hz
0x1902BD
2
+
0x193504
14
+
ADE7758
0x0
0x0
AVRMS[23:0]
2
8
2
7
(10)
2
6