AD1939WBSTZ Analog Devices Inc, AD1939WBSTZ Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD1939WBSTZ
Manufacturer Part Number
AD1939WBSTZ
Description
4-ADC 8-DAC Audio Codec W/on Chip PLL
Manufacturer
Analog Devices Inc
Type
General Purposer
Datasheet
1.AD1939YSTZ.pdf
(32 pages)
Specifications of AD1939WBSTZ
Data Interface
Serial
Resolution (bits)
24 b
Number Of Adcs / Dacs
4 / 8
Sigma Delta
Yes
S/n Ratio, Adcs / Dacs (db) Typ
94 / 94
Dynamic Range, Adcs / Dacs (db) Typ
105 / 110
Voltage - Supply, Analog
3 V ~ 3.6 V
Voltage - Supply, Digital
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD1939WBSTZ
Manufacturer:
ADI
Quantity:
70
AD1939
master clock. In addition, it is especially important that the
clock signal not pass through an FPGA, CPLD, or other large
digital chip (such as a DSP) before being applied to the
AD1939. In most cases, this induces clock jitter due to the
sharing of common power and ground connections with other
unrelated digital output signals. When the PLL is used, jitter in
the reference clock is attenuated above a certain frequency
depending on the loop filter.
RESET AND POWER-DOWN
The function of the RST pin sets all the control registers to their
default settings. To avoid pops, reset does not power down the
analog outputs. After RST is deasserted and the PLL acquires
lock condition, an initialization routine runs inside the
AD1939. This initialization lasts for approximately 256 master
clock cycles.
The power-down bits in the PLL and Clock Control 0, DAC
Control 1, and ADC Control 1 registers power down the
respective sections. All other register settings are retained. To
guarantee proper startup, the RST pin should be pulled low by
an external resistor.
Table 11. Standalone Mode Selection
ADC Clocks
Slave
Master
CLATCH
CCLK
COUT
CIN
t
COE
t
CLS
D23
CIN
0
0
t
CCP
D22
t
COD
D9
D9
t
CCH
COUT
0
1
Figure 11. Format of the SPI Signal
t
t
CDS
CCL
D8
D8
Rev. C | Page 14 of 32
t
CDH
SERIAL CONTROL PORT
The AD1939 has an SPI control port that permits programming
and reading back of the internal control registers for the ADCs,
DACs, and clock system. A standalone mode is also available for
operation without serial control; it is configured at reset using the
serial control pins. All registers are set to default, except the
internal MCLK enable is set to 1 and ADC BCLK and LRCLK
master/slave is set by the COUT pin. Standalone mode only
supports stereo mode with an I
rate. Refer to Table 11 for details. It is recommended to use a
weak pull-up resistor on CLATCH in applications that have a
microcontroller. This pull-up resistor ensures that the AD1939
recognizes the presence of a microcontroller.
The SPI control port of the AD1939 is a 4-wire serial control
port. The format is similar to the Motorola SPI format except
the input data-word is 24 bits wide. The serial bit clock and
latch can be completely asynchronous to the sample rate of the
ADCs and DACs. Figure 11 shows the format of the SPI signal.
The first byte is a global address with a read/write bit. For the
AD1939, the address is 0x04, shifted left one bit due to the R/ W
bit. The second byte is the AD1939 register address and the
third byte is the data.
CCLK
0
0
t
CLH
2
S data format and 256 f
CLATCH
0
0
D0
D0
t
COTS
S
MCLK