EVAL-ADT7X10EBZ Analog Devices Inc, EVAL-ADT7X10EBZ Datasheet - Page 13
![Evaluation Board I.c.](/photos/9/19/91955/eval-adt7410ebz_sml.jpg)
EVAL-ADT7X10EBZ
Manufacturer Part Number
EVAL-ADT7X10EBZ
Description
Evaluation Board I.c.
Manufacturer
Analog Devices Inc
Specifications of EVAL-ADT7X10EBZ
Sensor Type
Temperature
Sensing Range
-55°C ~ 150°C
Interface
I²C
Sensitivity
±0.5°C
Voltage - Supply
2.7 V ~ 5.5 V
Embedded
No
Utilized Ic / Part
ADT7410
Silicon Manufacturer
Analog Devices
Silicon Core Number
ADT7410
Kit Application Type
Sensing - Temperature
Application Sub Type
Temperature Sensor
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
EVAL-ADT7410EBZ
EVAL-ADT7410EBZ
EVAL-ADT7410EBZ
REGISTERS
The ADT7410 contains 14 registers:
•
•
•
•
•
•
All registers are eight bits wide. The temperature value registers,
the status register, and the ID register are read-only. The software
reset is a write-only register. On power-up, the address pointer
register is loaded with 0x00 and points to the temperature value
register MSB.
Table 6. ADT7410 Registers
Register
Address
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x2F
Table 8. Temperature Value MSB Register (Register Address 0x00)
Bit
[8:14]
[15]
Table 9. Temperature Value LSB Register (Register Address 0x01)
Bit
[0]
[1]
[2]
[3:7]
Nine temperature registers
A status register
An ID register
A configuration register
An address pointer register
A software reset
Default
Value
0
0
0
00000
Description
Temperature value most significant byte
Temperature value least significant byte
Status
Configuration
T
T
T
T
T
T
T
ID
Software reset
HIGH
HIGH
LOW
LOW
CRIT
CRIT
HYST
Default Value
0000000
0
setpoint most significant byte
setpoint least significant byte
setpoint most significant byte
setpoint least significant byte
setpoint most significant byte
setpoint least significant byte
setpoint
Type
R
R
R
R
Name
T
T
T
Temp
LOW
HIGH
CRIT
flag/LSB2
flag/LSB0
flag/LSB1
R
R
Type
Description
Flags a T
resolution). When the temperature value is below T
Contains the Least Significant Bit 0 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Flags a T
resolution). When the temperature value is above T
Contains the Least Significant Bit 1 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Flags a T
resolution). When the temperature value exceeds T
Contains the Least Significant Bit 2 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Temperature value in twos complement format.
Name
Temp
Sign
Power-On
Default
0x00
0x00
0x00
0x00
0x20 (64°C)
0x00 (64°C)
0x05 (10°C)
0x00 (10°C)
0x49 (147°C)
0x80 (147°C)
0x05 (5°C)
0xCX
0xXX
LOW
HIGH
CRIT
event if the configuration register, Register Address 0x03[7] = 0 (13-bit
event if the configuration register, Register Address 0x03[7] = 0 (13-bit
event if the configuration register, Register Address 0x03[7] = 0 (13-bit
Description
Temperature value in twos complement format
Sign bit, indicates if the temperature value is negative or positive
Rev. 0 | Page 13 of 24
ADDRESS POINTER REGISTER
This register is always the first register written to during a write
to the ADT7410. It should be set to the address of the register
to which the write or read transaction is intended. Table 7
shows the register address of each register on the ADT7410.
The default value of the address pointer register is 0x00.
Table 7. Address Pointer Register
P7
ADD7
TEMPERATURE VALUE REGISTERS
The temperature value most significant byte (MSB) and tem-
perature value least significant byte (LSB) registers store the
temperature measured by the internal temperature sensor.
The temperature is stored in twos complement format with
the MSB being the temperature sign bit. When reading from
these registers, the eight MSBs (Bit 7 to Bit 15) are read first
from Register Address 0x00 and then the eight LSBs (Bit 0 to
Bit 7) are read from Register Address 0x01. Only the tempera-
ture value most significant byte (Register Address 0x00) needs to
be loaded into the address pointer register as the address pointer
autoincrements to the Temperature value least significant byte
address (Register Address 0x01).
Bit 0 to Bit 2 are event alarm flags for T
the ADC is configured to convert the temperature to a 16-bit
digital value then Bit 0 to Bit 2 are no longer used as flag bits
and are instead used as the LSB bits for the extended digital value.
P6
ADD6
P5
ADD5
HIGH
CRIT
LOW
P4
ADD4
, this bit it set to 1.
, this bit it set to 1.
, this bit it set to 1.
P3
ADD3
CRIT
, T
P2
ADD2
HIGH
, and T
ADT7410
P1
ADD1
LOW
. When
P0
ADD0