MF-RX012/250U-15-0 Bourns Inc., MF-RX012/250U-15-0 Datasheet - Page 11
![PTC - RADIAL LEADED](/photos/1/32/13213/mf-rx160_mf-rx375_mf-rx300_mf-rx250_mf-rx185_mf-rx135_mf-rx110_sml.jpg)
MF-RX012/250U-15-0
Manufacturer Part Number
MF-RX012/250U-15-0
Description
PTC - RADIAL LEADED
Manufacturer
Bourns Inc.
Series
MF-RX/250r
Specifications of MF-RX012/250U-15-0
Voltage - Max
250V
Current - Max
3A
Current - Hold (ih) (max)
120mA
R Min/max
6.000 ~ 10.00 Ohm
Package / Case
Radial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Trip (it)
-
Time To Trip
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
How To Order
Agency File Numbers
MSMF = Surface Mount
SMHT = High Temp. Surface Mount
Bourns® Multifuse® Product Designator
Series
Hold Current, I hold
Voltage Options:
Packaging Options
NSMF = Surface Mount
SMDF = Surface Mount
USMF = Surface Mount
PSMF = Surface Mount
RHT = High Temp. Radial Mount
VSN = Axial Leaded Strap
Max. Interrupt Voltage, V
Construction Options:
Resistance Sorted**
(see individual data sheets)
Resistance Bins of 0.5 Ω***
SVS = Axial Leaded Strap
SM = Surface Mount
***Radial Leaded products only.
RG = Radial Leaded
RX = Radial Leaded
LR = Axial Leaded Strap
VS = Axial Leaded Strap
**Telecom Radial Leaded products only.
LS = Axial Leaded Strap
- AP = Ammo-Pak
D = Disk Configuration
R = Radial Leaded
*Axial Leaded Strap products only.
UL File Number................................................E 174545S
CSA File Number .............................................CA 110338
TÜV File Number ............................................R2057213
S = Axial Leaded Strap
- 0 = Bulk Packaging
- 2 = Tape and Reel
SS = Slotted Lead Option (two sides)*
05 = 0.5 Ω
N = Narrow Device Option (3.6 mm)*
U = Uncoated
T = Pretripped **
S = Slotted Lead Option (one side)*
MF - RX 012/250 U - A 05 - 2
11
Definitions
Agency Approvals
Current, Hold (I hold )
Current, Maximum (I max )
Current, Trip (I trip )
Fault Current
Positive Temperature Coefficient (PTC)
Resistance, Post Trip (R 1max )
Resistance, Post Reflow (R 1max )
Voltage, Maximum (V max )
Product Selection Worksheet
1. What is the normal circuit operating current (I hold )
2. What is the maximum circuit voltage (V max )
3. What is the maximum fault current (I max )
4. What is the preferred form factor
Note: Other factors including thermal derating and time to
trip characteristics may be important application
considerations. Please refer to the full Bourns® data sheet of
each product at www.bourns.com/multifuse.
Bourns® PPTCs are certified under UL, CSA, IEC and
TÜV registration programs.
The maximum current a PPTC device can pass without
interruption.
The maximum fault current a PPTC device can
withstand without damage at the rated voltage.
The minimum current that will switch a PPTC from the
low resistance to the high resistance state.
The peak current that flows through a PPTC or wire
during a short circuit or arc back.
A characteristic of the PPTC device that describes the
large increase in resistance as the device reaches its
switching (trip) temperature.
The maximum resistance one hour after a PPTC device
has been tripped and power has been removed.
The maximum resistance one hour after a PPTC surface
mount device has been reflow soldered.
The maximum voltage a PPTC device can withstand
without damage at the rated current.