4301-DEMO THAT Corporation, 4301-DEMO Datasheet - Page 8

• Manufacturer Part Number: 4301-DEMO
• Description: Audio Modules & Development Tools Dynamics Processor Demo Board
• Manufacturer: THAT Corporation

Specifications of 4301-DEMO

• Description/function: Audio DSPs
• Operating Supply Voltage: 15 V
• Product: Audio Modules
• For Use With/related Products: THAT4301
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Page 8
value of the input signal current. Some ac component
(at twice the input frequency) remains superimposed
on the dc output. The ac signal is attenuated by a
log-domain filter, which constitutes a single-pole
rolloff with cutoff determined by an external capaci-
tor and a programmable dc current.
RMS IN pin. This input is a virtual ground, so a re-
sistor (R
put voltages to the desired current. The level detector
is capable of accurately resolving signals well below
10 mV (with a 10 kW input resistor). However, if the
detector is to accurately track such low-level signals,
ac coupling is normally required.
placed well below the frequency range of interest. For
an audio-band detector, a typical value would be
5 Hz, or a 32 ms time constant (t). The filter’s time
constant is determined by an external capacitor at-
tached to the C
(I
grammed via the I
I
time constant t is approximately equal to 0.026 C
Note that, as a result of the mathematics of RMS de-
tection, the attack and release time constants are
fixed in their relationship to each other.
same constant of proportionality as the VCA gain
control: 6.5 mV/dB. The detector’s 0 dB reference
(I
determined by I
tector output stage is capable of sinking or sourcing
100 mA.
tor circuitry and that of the THAT 2252 RMS Detec-
tor are as follows:
CT
CT
in0
) connected to C
, the input current which causes 0 V output), is
As in the VCA, input signals are currents to the
The log-domain filter cutoff frequency is usually
with a gain of approximately 1.1. The resulting
The dc output of the detector is scaled with the
Differences between the 4301’s RMS-Level Detec-
1) The rectifier in the 4301 RMS Detector is inter-
nally balanced by design, and cannot be balanced
via an external control. The 4301 will typically bal-
ance positive and negative halves of the input signal
within ±1.5%, but in extreme cases the mismatch
may reach ±15%. However, a 15% mismatch will
not significantly increase ripple-induced distortion
6
in Figure 2) is normally used to convert in-
T
T
pin, and an internal current source
as follows: I
T
THAT Corporation; 45 Sumner Street; Milford, Massachusetts 01757-1656; USA
pin: current in I
T
Tel: [phone]; Fax: [phone]; Web: www.thatcorp.com
. The current source is pro-
in0
= 9.6 A I
T
is mirrored to
m
Copyright © 2009, THAT Corporation
T
The de-
T
/I
T
.
The Opamps — in Brief
general purpose applications. All are 5 MHz opamps
with slew rates of approximately 2V/ms. All use bipo-
lar PNP input stages. However, the design of each is
optimized for its expected use. Therefore, to get the
most out of the 4301, it is useful to know the major
differences among these opamps.
the VCA, is intended for current-to-voltage conver-
sion. Its input noise performance, at 7 5 . nV
complements that of the VCA, adding negligible noise
at unity gain. Its output section is capable of driving a
2 kW load to within 2V of the power supply rails,
making it possible to use this opamp directly as the
output stage in single-ended designs.
noise voltage, at 6 5 . nV
choice for input stages. Note that its output drive ca-
pability is limited (in order to reduce the chip’s
power dissipation) to approximately ±3 mA. It is
comfortable driving loads of 5 kW or more to within
1V of the power supply rails.
processor. Its input noise parallels that of OA
its output drive capability parallels that of OA
in dynamics processors over that caused by signal
ripple alone.
2) The time constant of the 4301’s RMS detector is
determined by the combination of an external ca-
pacitor (connected to the C
programmable current source. The current source
is equal to 1.1 I
nected directly to the C
3) The 0 dB reference point, or level match, is not
adjustable via an external current source. However,
as in the 2252, the level match is affected by the
timing current, which, in this case, is drawn from
the I
4) The input stage of the 4301 RMS detector uses
integrated
bias-current corrected bipolar differential amplifier.
Input bias currents are therefore negligible, improv-
ing performance at low signal levels.
The three opamps in the 4301 are intended for
OA
OA
OA
3
1
2
, being internally connected to the output of
T
is the quietest opamp of the three. Its input
is intended primarily as a control-voltage
pin and mirrored internally to C
P-channel
T
. Normally, a resistor is not con-
T
Hz, makes it the opamp of
pin on the 4301.
FETs
Document 600069 Rev 03
T
pin) and an internal,
rather
T
.
than
1
.
3
, and
Hz,
a