WH50 10K JI Welwyn Components, WH50 10K JI Datasheet - Page 3

• Manufacturer Part Number: WH50 10K JI
• Description: RESISTOR, 50W 5% 10K
• Manufacturer: Welwyn Components
• Series: WH50r

Specifications of WH50 10K JI

• Resistance: 10kohm
• Resistance Tolerance: ± 5%
• Power Rating: 50W
• Voltage Rating: 1.25kV
• Resistor Element Material: Wirewound
• No. Of Pins: 2
• Svhc: No SVHC
• Temperature Coefficient: ± 50ppm/°C
• Resistor Case Style: Axial
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Aluminium Housed
Wirewound Resistors
Performance Data
Load at commercial rating: 1000hrs at 25°C
Load at CECC rating: 1000hrs at 25°C
Dry heat: 1000hrs at 200°C
Derating from 25°C
Short-term overload
Climatic sequence
Climatic category
Long-term damp heat
Temperature rapid change
Resistance to solder heat
Vibration and bump
Noise (in decade of frequency)
Insulation resistance
Pulse and overload performance
Note: A 0.05 ohm addition is to be added to the performance of all resistors < 10 ohms.
Application Notes
After soldering care should be taken to ensure that there are no flux residues on the end faces of the moulding
compound, otherwise insulation resistance will be reduced. The minimum surface tracking distances from termination
to casing are shown in the Physical Data tables as dimension Dt.
It is recommended that the resistor base should be coated with heatsink compound before mounting to obtain the
stated operating characteristics. The heatsink compound increases thermal conductivity to the heatsink.
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyn’s own test data and is considered accurate at time of print.
Welwyn Electronics Park, Bedlington, Northumberland, NE22 7AA, England. Tel: [phone] Fax: [phone] Web: www.welwyn-tt.com
Terminations
WH5-100
Material
Strength
Solderability
Pulse and Overload Performance
For short durations of ≤0.1s the energy graph should
be used. For longer durations the overload graph
applies.
Welwyn Components Limited
10
1
0.1
WH5&10
WH25-300
1
Pb-free solder dipped, copper clad steel
The terminations meet the requirements
of IEC 68.2.21
The terminations meet the requirements
of IEC 115-1, clause 4.17.3.2
Overload Duration (s)
WH5-50
10
100
WH100-300
ohms
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
μV/V
1000
CECC 40203-006
Requirements
10000
Not specified
Not specified
1000
100
1G min
0.1
10
0.25
0.25
0.25
1
0.01
1
1
1
1
1
1
WH200 & 300
Material
Strength
Solderability
0.1
Zero at 200°C, see derating graph
55/200/56
WH5 - 50
Maximum
0.25
0.25
0.25
0.5
1
1
1
1
1
0
1
Actual
Value (ohms)
M6 threaded steel terminal
Termination robustness 50N
Non-solderable
10
Typical
See graphs
0.025
0.05
0.4
0.4
0.4
0.2
0.4
0.2
0.1
10G min
100
0
1000
WH100 - 300
WH100: 0.5
Maximum
10000 100000
0.25
N/A
WH5
2
2
0
WH10
WH100
WH25
WH200
WH300
WH50