FM-RX2-433A-5V RF Solutions, FM-RX2-433A-5V Datasheet
FM-RX2-433A-5V
Specifications of FM-RX2-433A-5V
Related parts for FM-RX2-433A-5V
FM-RX2-433A-5V Summary of contents
Page 1
... ODULES FEATURES MINIATURE PACKAGE PLUG IN COMPATIBLE WITH FM-TX1 / RX1 EMC CONFORMANT TO ETS 300-683 TYPE APPROVED TO ETS 300-220 DATA RATES TO 40KBIT/S USABLE RANGE TO 300 METRES 418 & 433.92MHZ VERSIONS. SINGLE SUPPLY VOLTAGE FULLY SCREENED Transmitter - TX2 2 STAGE SAW CONTROLLED, FM MODULATED AT UPTO 40KBIT/S OPERATION FROM 2 ...
Page 2
... MHz unit has MPT 1340 type-approval for U.K. use and delivers -3dBm from a 5V supply at 5mA. Both modules measure 3.8 mm. The RX2 module is a double conversion FM superhet receiver capable of handling date rates of upto 40kbit/s. The SIL style RX2 receiver measures 17 4.5 mm. It will operate from a supply of 3-6V and draws 14mA when receiving ...
Page 3
... ODULES RX2 receiver DS000022 Rev D July ‘99 & R RANSMITTER . ( ENERATION < < > > 1999 REG No 277 4001, ENGLAND. FM-TX2-XXX ECEIVER ) FM-RX2-XXX < < > < > < < < Page 3 ...
Page 4
... Vcc = 3V RF power @ Vcc = 3V TX2-433-5V supply current @ Vcc = 5V RF power @ Vcc = harmonic Harmonics @ > 1GHz initial frequency accuracy overall frequency accuracy FM deviation (+/-) Modulation bandwidth @ -3dB Modulation distortion (THD) power up time to full RF note: DS000022 Rev D July ‘99 & R RANSMITTER ECEIVER . ( ENERATION ...
Page 5
... ODULES Electrical Performance: RX2 Receiver Figures apply to 5V versions unless noted otherwise Vcc = 5.0V, temperature 20 C unless noted otherwise DC LEVELS supply voltage, Vcc standard supply voltage, Vcc, 3V version supply current supply ripple data output high, 100 A source data output low, 100 A sink ...
Page 6
... ODULES Module test circuits The PNP transistor enables a CMOS compatible Carrier Detect signal to be derived from pin signal required pin 3 should be connected directly to pin 5 (Vcc) Module mounting considerations The modules may be mounted horizontally or vertically on an area of ground plane preferably close to the antenna to minimise feed length. The receiver and it’s antenna should be kept away from sources of interference (micro’ ...
Page 7
... ODULES Antenna requirements Three types of integral antenna are recommended and approved for use with the module: Helical Wire coil, connected directly to pin 2, open circuit at other end. This antenna is very efficient given it's small size (20mm x 4mm dia.). The helical is a high Q antenna, trim the wire length or expand the coil for optimum results ...
Page 8
... ODULES Type Approval in UK The TX2-418 is type approved in the UK to MPT1340 for use in Telemetry, Telecommand and In- Building alarm applications. CONFORMANCE to MPT1340 REQUIRES THAT: 1. The transmitting antenna must be one of the 3 variants given in the data sheet. Antenna structures which yield ERP gain are not permitted. ...
Page 9
... RX data rate: RX data rate applies to receivers only, the TX2 will handle fast or slow data. PART No FM-TX2-418-5V FM-TX2-418-3V FM-TX2-433-5V FM-TX2-433-3V FM-RX2-418A-5V FM-RX2-418F-5V FM-RX2-433A-5V FM-RX2-433F-5V FM-RX2-418A-3V FM-RX2-418F-3V FM-RX2-433A-3V FM-RX2-433F-3V Should you require further assistance, please call; Email sales@rfsolutions.co.uk Limitation of Liability The information furnished by RF Solutions Ltd. is believed to be accurate and reliable. RF Solutions Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its sub-assembly products without notice ...