GSM20-ANT RF Solutions, GSM20-ANT Datasheet
GSM20-ANT
Specifications of GSM20-ANT
Related parts for GSM20-ANT
GSM20-ANT Summary of contents
Page 1
... About GPRS: GPRS stands for General Packet Radio Services. The user can remain "ON" all the time and the data communication speed rivals that of a cable modem. Ordering Information Part No GSM100 GSM100T GSM20-ANT GSM20-CAB232 GSM20-DINRL GSM20-PSU DS100-1 May ’07 Description GSM Quad Band Modem, GPRS Class 10 ...
Page 2
GSM & GPRS Modem 1 SAFETY PRECUTIONS CHAPTER 1 CHAPTER 2 CHAPTER 3 CHAPTER 4 CHAPTER 5 CHAPTER 6 DS100-1 May ’07 CONTENTS INTRODUCTION INSTALLATION WORKING WITH MAESTRO 100 SPECIFICATION APPENDIX TROUBLESHOOTING ©2007 REG No 277 4001, ENGLAND. www.rfsolutions.co.uk 2 ...
Page 3
GSM & GPRS Modem 2 SAFETY PRECUTIONS The modem generates radio frequency (RF) power. When using the modem care must be taken on safety issues related to RF interference as well as regulations of RF equipment. Do not use your ...
Page 4
GSM & GPRS Modem 3 Maestro 100 is a ready-to-use GSM modem for voice, data, fax and SMS services. It also supports GPRS Class 10 for hi-speed data transfer. Maestro 100 can be easily controlled by using AT command for ...
Page 5
GSM & GPRS Modem 4 1.2.3. 15-PIN D-SUB Female connector (RS232 / Audio) - The connector provides serial link and audio link to the modem. Pin number Name 1 DCD 2 3 BOOT 4 MICROPHONE (+) 5 MICROPHONE (-) 6 ...
Page 6
GSM & GPRS Modem 5 A cable, included in the package shall be used for power supply connection: Connector Micro-Fit 3.0 I/O Parameters I/O In LOW voltage I/O In HIGH voltage I/O out max. sink current INTR Parameters Input LOW ...
Page 7
GSM & GPRS Modem 6 Pin Assignment Sub-D 15 Sub-D 9 (male) (female) 4P4C DS100-1 May ...
Page 8
GSM & GPRS Modem 7 2.1 Mounting the modem Use 2 pcs of M3 screw to mount the modem When using optional DIN rail mount please refer to document “Installation of DIN rail mount” Bottom view 2.2 Installing the SIM ...
Page 9
GSM & GPRS Modem 8 2.4 Connect the modem to external device You can use the optional ‘Y’ cable to connect the modem’s Sub-D connector to external controller/computer. Note : The modem CANNOT be connected to the ‘Line’ jack of ...
Page 10
GSM & GPRS Modem 9 3.1. Checking the modem (using Microsoft Windows XP HyperTerminal as example) 3.1.1. On the first time power-up you can use a terminal software to communicate with the modem through an RS-232 serial port. Following example ...
Page 11
GSM & GPRS Modem 10 3.1.3. Choose the correct Com port and baud rate settings (9600bps for Eco; 115200bps for others, 8bits, no parity bit, 1 stop bit). 3.1.4. On the terminal screen, type “AT” to check the “OK” response ...
Page 12
GSM & GPRS Modem 11 3.2. Basic Operation : Followings are examples of some AT commands. Please refer to the AT Command guide for a full description. Note : Issue AT+CMEE=1 to have extended error code (+CME ERROR) Description AT ...
Page 13
GSM & GPRS Modem 12 Bands 850 / 900 / 1800 / 1900 Mhz Support Data, SMS, Voice and Fax Max Power Output: 2W(900Mhz), 1W(1800Mhz) Group 3 FAX support (Class 1 and 2) GPRS Class B Class 10 (4Rx+1Tx or ...
Page 14
GSM & GPRS Modem 13 5.1 Factory settings The modem has the following factory settings. Please refer to the AT command document for the meaning of each setting. Related AT commands AT+IPR AT+IFC AT+ICF ATE AT&C AT&D ATQ ATV AT&S ...
Page 15
GSM & GPRS Modem 14 6.1 The modem’s LED does not light : Check if the modem has connected to a 5-32V power supply properly Check if the power connector is properly inserted Check the fuse on the power cord ...