74HCT4046AN NXP Semiconductors, 74HCT4046AN Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
74HCT4046AN
Manufacturer Part Number
74HCT4046AN
Description
74HCT CMOS, 74HCT4046, DIP16, 5V
Manufacturer
NXP Semiconductors
Datasheet
1.74HCT4046AD.pdf
(34 pages)
Specifications of 74HCT4046AN
Pll Type
VCO
Frequency
21MHz
Supply Voltage Range
4.5V To 5.5V
Digital Ic Case Style
DIP
No. Of Pins
16
Operating Temperature Range
-40°C To +125°C
Svhc
No SVHC (18-Jun-2010)
Operating
RoHS Compliant
Supply Current
8µA
Rohs Compliant
Yes
Base Number
74
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
74HCT4046AN
Manufacturer:
MT
Quantity:
238
Part Number:
74HCT4046AN
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Philips Semiconductors
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
DIP
S
The maximum permissible temperature of the solder is
260 C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
R
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 C, contact may be up to 5 seconds.
SO, SSOP and TSSOP
R
Reflow soldering techniques are suitable for all SO, SSOP
and TSSOP packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method.
1997 Nov 25
OLDERING BY DIPPING OR BY WAVE
EPAIRING SOLDERED JOINTS
EFLOW SOLDERING
Phase-locked-loop with VCO
stg max
). If the
33
Typical reflow temperatures range from 215 to 250 C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 C.
W
Wave soldering can be used for all SO packages. Wave
soldering is not recommended for SSOP and TSSOP
packages, because of the likelihood of solder bridging due
to closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering is used - and cannot be avoided for
SSOP and TSSOP packages - the following conditions
must be observed:
Even with these conditions:
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 C within
6 seconds. Typical dwell time is 4 seconds at 250 C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
R
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 C.
EPAIRING SOLDERED JOINTS
AVE SOLDERING
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow and must incorporate solder
thieves at the downstream end.
Only consider wave soldering SSOP packages that
have a body width of 4.4 mm, that is
SSOP16 (SOT369-1) or SSOP20 (SOT266-1).
Do not consider wave soldering TSSOP packages
with 48 leads or more, that is TSSOP48 (SOT362-1)
and TSSOP56 (SOT364-1).
74HC/HCT4046A
Product specification