MB9BF104RPMC-GE1 Fujitsu Semiconductor America Inc, MB9BF104RPMC-GE1 Datasheet

no-image

MB9BF104RPMC-GE1

Manufacturer Part Number
MB9BF104RPMC-GE1
Description
IC MCU 32BIT 256KB FLASH 120LQFP
Manufacturer
Fujitsu Semiconductor America Inc
Series
FM3 MB9B100r

Specifications of MB9BF104RPMC-GE1

Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
80MHz
Connectivity
CSIO, EBI/EMI, I²C, LIN, UART/USART
Peripherals
DMA, LVD, POR, PWM, WDT
Number Of I /o
100
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 16x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
120-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
865-1117
FUJITSU SEMICONDUCTOR
32-bit ARM
FM3 MB9B100 Series
MB9BF104N/R, F105N/R, F106N/R
 DESCRIPTION
Copyright  2010-2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2011.1
DATA SHEET
The MB9B100 Series are a highly integrated 32-bit microcontroller that target for high-performance and
cost-sensitive embedded control applications.
The MB9B100 Series are based on the ARM Cortex-M3 Processor and on-chip Flash memory and SRAM,
and peripheral functions, including Motor Control Timers, ADCs and Communication Interfaces (UART,
SIO, I
Note: ARM and Cortex-M3 are the trademarks of ARM Limited in the EU and other countries.
2
C, LIN).
TM
Cortex
TM
-M3 based Microcontroller
DS706-00007-1v0-E

Related parts for MB9BF104RPMC-GE1

MB9BF104RPMC-GE1 Summary of contents

Page 1

FUJITSU SEMICONDUCTOR DATA SHEET 32-bit ARM Cortex TM FM3 MB9B100 Series MB9BF104N/R, F105N/R, F106N/R  DESCRIPTION The MB9B100 Series are a highly integrated 32-bit microcontroller that target for high-performance and cost-sensitive embedded control applications. The MB9B100 Series are based on ...

Page 2

MB9B100 Series  FEATURES  32-bit ARM Cortex-M3 Core ・ Processor version: r2p0 ・ 80MHz Frequency Operation ・ Memory Protection Unit (MPU): improve the reliability of an embedded system ・ Integrated Nested Vectored Interrupt Controller (NVIC): 1 NMI ...

Page 3

LIN protocol Rev.2.1 supported ・ Full-duplex double buffer ・ Master/Slave mode supported ・ LIN break field generate (can be changed 13-16bit length) ・ LIN break delimiter generate (can be changed 1-4bit length) ・ Various error detect functions available ...

Page 4

MB9B100 Series  Multi-function Timer (Max. 2unit) The Multi-function timer is composed of the following blocks. ・ 16-bit free-run timer × 3ch/unit ・ Input capture × 4ch/unit ・ Output compare × 6ch/unit ・ A/D activating compare × 3ch/unit ・ Waveform ...

Page 5

CRC (Cyclic Redundancy Check) Accelerator The CRC accelerator helps a verify data transmission or storage integrity. CCITT CRC16 and IEEE-802.3 CRC32 are supported. ・ CCITT CRC16 Generator Polynomial: 0x1021 ・ IEEE-802.3 CRC32 Generator Polynomial: 0x04C11DB7  Clock and Reset ...

Page 6

MB9B100 Series  PRODUCT LINEUP  Memory size Product device MB9BF104N/R On-chip Flash 256Kbyte On-chip RAM 32Kbyte  Function Product device Pin count CPU Freq. Power supply voltage range DMAC External Bus Interface MF Serial Interface 2 (UART/CSIO/LIN/I C) Base ...

Page 7

PACKAGES Product name Package LQFP: FPT-100P-M20*/M23 LQFP: FPT-120P-M21 BGA: BGA-112P-M04 : Supported * : ES product only Note : Refer to "PACKAGE DIMENSIONS" for detailed information on each package. DS706-00007-1v0-E MB9B100 Series MB9BF104N MB9BF104R MB9BF105N MB9BF105R MB9BF106N MB9BF106R  ...

Page 8

MB9B100 Series  PIN ASSIGNMENT  FPT-100P-M20/M23 <Note> The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for ...

Page 9

FPT-120P-M21 <Note> The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the ...

Page 10

MB9B100 Series  BGA-112P-M04 <Note> The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. ...

Page 11

PIN DESCRIPTION The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the ...

Page 12

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 I/O circuit Pin name type P55 SCK6_0 (SCL6_0) ADTG_1 7 E RTO15_0 (PPG14_0) MDATA5 P56 SIN1_0 ...

Page 13

Pin no. LQFP-100 BGA-112 LQFP-120 DS706-00007-1v0-E MB9B100 Series I/O circuit Pin name type P31 BIN0_0 TIOB1_1 15 E SCK6_1 (SCL6_1) INT04_2 MDATA7 P32 ZIN0_0 ...

Page 14

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 I/O circuit Pin name type P39 23 E ...

Page 15

Pin no. LQFP-100 BGA-112 LQFP-120 DS706-00007-1v0-E MB9B100 Series I/O circuit ...

Page 16

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 I/O circuit Pin name type P4A TIOB1_0 IC11_1 46 E BIN0_1 SCK3_2 (SCL3_2) MAD14 P4B TIOB2_0 ...

Page 17

Pin no. LQFP-100 BGA-112 LQFP-120 - - - - L10 50 L11 51 K11 52 J11 53 J10 - K10 - H10 DS706-00007-1v0-E MB9B100 Series ...

Page 18

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 58 G10 H11 61 F11 62 G11 F10 E11 67 E10 18 I/O circuit Pin name type P16 AN06 68 F SCK0_1 ...

Page 19

Pin no. LQFP-100 BGA-112 LQFP-120 D11 - - - - - - - - - B10 - DS706-00007-1v0-E MB9B100 Series I/O circuit Pin name type P1D AN13 78 F CTS4_1 IC03_1 MDATA13 ...

Page 20

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 71 D10 C11 74 C10 75 A11 76 A10 B11 I/O circuit Pin name type P23 ...

Page 21

Pin no. LQFP-100 BGA-112 LQFP-120 DS706-00007-1v0-E MB9B100 Series I/O circuit Pin name type P06 TRACED1 TIOB5_2 98 E SOT4_2 (SDA4_2) INT01_1 P07 TRACED2 99 ...

Page 22

MB9B100 Series Pin no. LQFP-100 BGA-112 LQFP-120 I/O circuit Pin name type P0E CTS4_0 106 ...

Page 23

Pin no. LQFP-100 BGA-112 LQFP-120 100 A1 DS706-00007-1v0-E MB9B100 Series I/O circuit Pin name type P60 SIN5_0 116 E TIOA2_2 INT15_1 117 VCC 118 P80 H 119 P81 H 120 VSS Pin ...

Page 24

MB9B100 Series  SIGNAL DESCRIPTION The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. ...

Page 25

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 26

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 27

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 28

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 29

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 30

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 31

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 32

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 33

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 34

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 35

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 36

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 37

The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended port function ...

Page 38

MB9B100 Series The number after the underscore ("_") in pin names such as XXX_1 and XXX_2 indicates the relocated port number. For these pins, there are multiple pins that provide the same function for the same channel. Use the extended ...

Page 39

I/O CIRCUIT TYPE Type Circuit Standby mode control B Pull-up resistor C DS706-00007-1v0-E MB9B100 Series Remarks ・ Oscillation feedback resistor : Approximately 1MΩ ・ With Standby mode control Clock input ・ CMOS level hysteresis input ・ ...

Page 40

MB9B100 Series Type Circuit D P-ch P-ch X1A N-ch R Standby mode control R P-ch P-ch X0A N-ch 40 ・ possible to select the low speed oscillation / GPIO function. When the low speed oscillation is selected. Digital ...

Page 41

Type Circuit E P-ch P-ch N-ch F P-ch P-ch N-ch Input control DS706-00007-1v0-E MB9B100 Series Remarks ・ CMOS level output ・ CMOS level hysteresis input ・ With pull-up resistor control ・ With standby mode control ・ pull-up resistor : Approximately ...

Page 42

MB9B100 Series Type Circuit G P-ch P-ch N-ch H P-ch 42 Digital output Digital output Pull-up resistor control Digital input Standby mode control Digital output N-ch Digital output Digital input Standby mode control Remarks ・ CMOS level output ・ CMOS ...

Page 43

PRECAUTIONS FOR HANDLING THE DEVICES Any semiconductor devices have inherently a certain rate of failure. The possibility of failure is greatly affected by the conditions in which they are used (circuit conditions, environmental conditions, etc.). This page describes precautions ...

Page 44

MB9B100 Series ・ Observance of Safety Regulations and Standards Most countries in the world have established standards and regulations regarding safety, protection from electromagnetic interference, etc. Customers are requested to observe applicable regulations and standards in the design of products. ...

Page 45

Precautions for Package Mounting Package mounting may be either lead insertion type or surface mount type. In either case, for heat resistance during soldering, you should only mount under FUJITSU's recommended conditions. For detailed information about mount conditions, contact ...

Page 46

MB9B100 Series ・ Static Electricity Because semiconductor devices are particularly susceptible to damage by static electricity, you must take the following precautions: ・ Maintain relative humidity in the working environment between 40% and 70%. Use of an apparatus for ion ...

Page 47

HANDLING DEVICES  Power supply pins In products with multiple VCC and VSS pins, respective pins at the same potential are interconnected within the device in order to prevent malfunctions such as latch-up. However, all of these pins should ...

Page 48

MB9B100 Series  C Pin As this series includes an internal regulator, always connect a bypass capacitor of approximately 4.7 µF to the C pin for use by the regulator.  Mode pins (MD0, MD1) Connect the MD pin (MD0, ...

Page 49

BLOCK DIAGRAM MB9BF104/105/106 TRSTX,TCK TDI,TMS SWJ-DP ETM TDO ROM TRACED[3:0], TPIU Table TRACECLK Cortex-M3 Core I @80MHz(Max.) D MPU NVIC Sys Dual-Timer WatchDog Timer (Software) Clock Reset Generator INITX WatchDog Timer (Hardware) CSV RST CLK Main X0 PLL Osc ...

Page 50

MB9B100 Series  MEMORY MAP  MB9B100 Series Memory Map(1) 0xFFFF_FFFF 0xE010_0000 0xE000_0000 0x6000_0000 0x4400_0000 0x4200_0000 0x4000_0000 0x2400_0000 0x2200_0000 0x2008_0000 0x2000_0000 0x1FF8_0000 Please refer to 0x0010_2000 the next page for the memory size 0x0010_0000 details. 0x0000_0000 50 0x41FF_FFFF Reserved 0x4006_4000 ...

Page 51

MB9B100 Series Memory Map(2) 0x2008_0000 Reserved 0x2000_8000 On Chip SRAM 32kbyte 0x2000_0000 Code SRAM 32Kbyte 0x1FFF_8000 Reserved 0x0010_2000 CR triming 0x0010_1000 Security 0x0010_0000 Reserved 0x0008_0000 FLASH 512Kbyte 0x0000_0000 MB9BF106N/R DS706-00007-1v0-E MB9B100 Series 0x2008_0000 Reserved 0x2000_6000 On Chip SRAM 24kbyte ...

Page 52

MB9B100 Series  Peripheral Address Map Start address End address 0x4000_0000 0x4000_0FFF 0x4000_1000 0x4000_FFFF 0x4001_0000 0x4001_0FFF 0x4001_1000 0x4001_1FFF 0x4001_2000 0x4001_2FFF 0x4001_3000 0x4001_4FFF 0x4001_5000 0x4001_5FFF 0x4001_6000 0x4001_FFFF 0x4002_0000 0x4002_0FFF 0x4002_1000 0x4002_1FFF 0x4002_2000 0x4002_3FFF 0x4002_4000 0x4002_4FFF 0x4002_5000 0x4002_5FFF 0x4002_6000 0x4002_6FFF 0x4002_7000 0x4002_7FFF ...

Page 53

PIN STATUS IN EACH CPU STATE The terms used for pin status have the following meanings. ・ INITX=0 This is the period when the INITX pin is the "L" level. ・ INITX=1 This is the period when the INITX ...

Page 54

MB9B100 Series  LIST OF PIN STATUS Power-on reset or low voltage detection state Pin status Function group Power supply type unstable A Main crystal Input enabled oscillator input pin B Main crystal H output/ oscillator output Internal input pin ...

Page 55

Power-on reset or low voltage detection state Pin status Function group Power supply type unstable G Trace selected Setting disabled GPIO selected, Hi-Z or other than above resource selected H External interrupt Setting enabled selected disabled GPIO selected, Hi-Z or ...

Page 56

MB9B100 Series Power-on reset or low voltage detection state Pin status Function group Power supply type unstable K Analog input Hi-Z selected GPIO selected, Setting or other than disabled above resource selected L External interrupt Setting enabled selected disabled Analog ...

Page 57

Power-on reset or low voltage detection state Pin status Function group Power supply type unstable N GPIO selected Setting disabled Sub crystal Hi-Z/ oscillator output Internal input pin fixed at "0" O GPIO selected Hi Oscillation is stopped ...

Page 58

MB9B100 Series  ELECTRICAL CHARACTERISTICS This section describes the electrical characteristics of MB9B100 series.  Absolute Maximum Ratings / Recommended Operating Conditions The following tables show the absolute maximum ratings and recommended operating conditions. 1. Absolute Maximum Ratings Parameter Power ...

Page 59

Recommended Operating Conditions Parameter Symbol Conditions Power supply voltage Analog power supply voltage AVcc Analog reference voltage AVRH FPT-120P-M21 Operating FPT-100P-M20 Temperature FPT-100P-M23 BGA-112P-M04 <WARNING> The recommended operating conditions are required in order to ensure the normal operation of ...

Page 60

MB9B100 Series  DC Characteristics The following tables show the DC characteristics. 1. Current rating Pin Parameter Symbol name Normal operation Icc Normal operation Power supply Vcc current Normal operation (sub oscillation) Normal operation SLEEP operation SLEEP operation Iccs SLEEP ...

Page 61

Pin Parameter Symbol name I CCH Power supply current Vcc I CCT Low voltage detection circuit (LVD) I CCLVD power supply current *1:When all ports are fixed. *2: When setting it to 4MHz by trimming. DS706-00007-1v0-E MB9B100 Series Value ...

Page 62

MB9B100 Series 2. Pin Characteristics Parameter Symbol Pin name "H" level CMOS input hysteresis voltage V IHS input pin, (hysteresis MD0,1 input) "L" level input CMOS voltage hysteresis V ILS (hysteresis input pin, input) MD0,1 4mA type "H" level V ...

Page 63

AC Characteristics The following tables show the AC characteristics. (1) Main Clock Input Characteristics Pin Parameter Symbol name Input frequency Input clock cycle t CYLH X1 Input clock pulse - width Input clock rise t CF ...

Page 64

MB9B100 Series (2) Sub Clock Input Characteristics Pin Parameter Symbol name Input frequency F CL X0A X1A Input clock cycle t CYLL Input clock pulse - width 0.8×Vcc X0A (3) Built-in CR Oscillation Characteristics ・ Built-in high-speed CR Parameter Symbol ...

Page 65

Operating Conditions of PLL Parameter PLL oscillation stabilization wait time (LOCK UP time)* PLL input clock frequency PLL multiple rate PLL macro oscillation clock frequency *: Time from when the PLL starts operating until the oscillation stabilizes. (5) Reset ...

Page 66

MB9B100 Series (7) External Bus Timing ・ Asynchronous SRAM Mode Parameter Symbol MOEX t OEW Min pulse width MOEX   t OEL - AV MAD24 to 00 Address delay time MOEX   t OEH - AX Address delay ...

Page 67

S RAM read CSL MAD ATA rite t ...

Page 68

MB9B100 Series ・ NAND FLASH mode Parameter Symbol MNREX t NREW Min pulse width Data set NRE  MNREX  tiime MDATA15 to 0 Vcc  4.5V MNREX   NRE Data hold ...

Page 69

LAS H read ATA15 LAS H wr ite t CYC H- ...

Page 70

MB9B100 Series (8) Base Timer Input Timing ・ Timer input timing Parameter Symbol TIOAn/TIOBn t TIWH Input pulse width (when using as t TIWL t TIWH ECK V IHS TIN ・ Trigger input timing Parameter Symbol TIOAn/TIOBn t TRGH Input ...

Page 71

UART Timing ・ Synchronous serial (SPI = 0, SCINV = 0) Parameter Symbol Serial clock cycle time tSCYC SCK   SOT delay time tSLOVI SIN  SCK  setup time tIVSHI SCK   SIN hold time tSHIXI ...

Page 72

MB9B100 Series ...

Page 73

Synchronous serial(SPI = 0, SCINV = 1) Parameter Symbol Serial clock cycle time tSCYC SCK   SOT delay time tSHOVI SIN  SCK  setup time tIVSLI SCK   SIN hold time tSLIXI Serial clock "L" pulse ...

Page 74

MB9B100 Series ...

Page 75

Synchronous serial(SPI = 1, SCINV = 0) Parameter Symbol Serial clock cycle time tSCYC SCK   SOT delay time tSHOVI SIN  SCK  setup time tIVSLI SCK   SIN hold time tSLIXI SOT  SCK  ...

Page 76

MB9B100 Series SCK tSOVLI VOH SOT VOL tIVSLI VIH SIN VIL SCK * SOT VO L tIVSLE VIH SIN VIL *2 : Changes when writing to TDR register 76 tSCYC VOH VOL tSHOVI tSLIXI VIH VIL MS bit=0 ...

Page 77

Synchronous serial(SPI = 1, SCINV = 1) Parameter Symbol Serial clock cycle time tSCYC SCK   SOT delay time tSLOVI SIN  SCK  setup time tIVSHI SCK  SIN hold time tSHIXI SOT  SCK  delay ...

Page 78

MB9B100 Series SCK tSOV HI VOH SOT VOL tIVSHI VIH SIN VIL SCK VOH SOT VOL tI VSHE VIH SIN VIL ・ External clock(EXT = 1) : asynchronous only Parameter Symbol Conditions Serial clock "L" pulse width tSLSH Serial clock ...

Page 79

External input timing Parameter Symbol Pin name ADTG FRCKx t INH Input pulse width ICxx t INL DTTIxX INT00 to INT15, NMIX * indicates the peripheral clock cycle time except stop when in stop mode. CYCP *2 ...

Page 80

MB9B100 Series (11) Quadrature Position/Revolution Counter timing Parameter Symbol AIN pin "H" width tAHL AIN pin "L" width tALL BIN pin "H" width tBHL BIN pin "L" width tBLL BIN rise time from tAUBU AIN pin "H" level AIN fall ...

Page 81

BIN tBUAU tAUBD AIN tAHL tZHL ZIN ZIN tZABE AIN/BIN DS706-00007-1v0-E MB9B100 Series tBLL tBDAD tADBU tALL tZLL tABEZ 81 ...

Page 82

MB9B100 Series 2 (12 timing Parameter Symbol SCL clock frequency fSCL (Repeated) START condition hold time tHDSTA SDA   SCL  SCLclock "L" width tLOW SCLclock "H" width tHIGH (Repeated) START setup time tSUSTA SCL   ...

Page 83

ETM timing Parameter Symbol Pin name TRACECLK Data hold t ETMH TRACED3 - 0 Note: When the external load capacitance = 50pF ...

Page 84

MB9B100 Series (14) JTAG timing Parameter Symbol Pin name TMS,TDI setup TCK t JTAGS time TMS,TDI TCK TMS,TDI hold time t JTAGH TMS,TDI TCK TDO delay time t JTAGD TDO Note: When the external load capacitance = 50pF ...

Page 85

A/D Converter This chapter shows the electrical characteristics for the A/D converter. 1. Electrical characteristics for the A/D converter. Pin Parameter name Resolution - Linearity error - Differential linearity - error AN0 Zero transition voltage to AN15 AN0 ...

Page 86

MB9B100 Series (Continued) Analog input pin Rext Analog signal source (Equation 1) Ts  ( Rin + Rext ) × Cin × Sampling time Rin : input resistance of A/D = 0.93kΩ input resistance of A/D = ...

Page 87

Definition of 12-bit A/D Converter Terms ・ Resolution : Analog variation that is recognized by an A/D converter. ・ Linearity error : Deviation of the line between the zero-transition point (0b0000000000000b000000000001) and the full-scale transition point (0b1111111111100b111111111111) from the ...

Page 88

MB9B100 Series  Low voltage detection characteristics 1. Low voltage detection reset Parameter Symbol Conditions Detected voltage VDL Released voltage VDH 2. Interrupt of low voltage detection Parameter Symbol Conditions Detected voltage VDL SVHI = 0000 Released voltage VDH Detected ...

Page 89

Flash Memory Write/Erase Characteristics Parameter Min Large Sector Sector erase - time Small Sector Half word (16 bit) - write time Chip erase time - Erase/write cycles and data hold time Erase/write cycles Data hold time (cycle) 1,000 10,000 ...

Page 90

MB9B100 Series  EXAMPLE OF CHARACTERISTIC Power supply current (PLL run mode, PLL sleep mode) Icc normal operation(PLL) temperature characteristics Vcc:5.5V, CPU:80MHz, Peripheral:40MHz,FLASH 2Wait 120 110 100 -40 -30 -20 ...

Page 91

Power supply current (Sub timer mode) I timer mode(sub oscillation) temperature characteristics CCT Vcc:5.5V, LVD is Off 500 450 400 350 300 250 200 150 100 50 0 -40 -30 -20 - Temperature Ta[℃] Power ...

Page 92

... MB9B100 Series  ORDERING INFORMATION Part number MB9BF104NPMC MB9BF105NPMC MB9BF106NPMC MB9BF104RPMC MB9BF105RPMC MB9BF106RPMC MB9BF104NBGL MB9BF105NBGL MB9BF106NBGL * : ES product only 92 Package Plastic・LQFP(0.5mm pitch),100-pin (FPT-100P-M20*/M23) Plastic・LQFP(0.5mm pitch),100-pin (FPT-100P-M20*/M23) Plastic・LQFP(0.5mm pitch),100-pin (FPT-100P-M20*/M23) Plastic・LQFP(0.5mm pitch),120-pin (FPT-120P-M21) Plastic・ ...

Page 93

PACKAGE DIMENSIONS 100-pin plastic LQFP (FPT-100P-M20) 100-pin plastic LQFP (FPT-100P-M20) 16.00±0.20(.630±.008)SQ *14.00±0.10(.551±.004) INDEX 100 1 0.50(.020) 0.20 ±0.05 (.008 ±.002) 2005 -2010 FUJITSU SEMICONDUCTOR LIMITED F100031S-c-3-5 C Please check the latest package dimension at the following URL. ...

Page 94

MB9B100 Series (Continued) 100-pin plastic LQFP (FPT-100P-M23) 100-pin plastic LQFP (FPT-100P-M23) 16.00±0.20(.630 ±.008 14.00±0.10(.551 ±.004 INDEX 100 1 0.50(.020) 0.22±0.05 (.009±.002) 2009-2010 FUJITSU SEMICONDUCTOR LIMITED F100034S-c-3-4 C Please check the latest package dimension at the ...

Page 95

LQFP (FPT-120P-M21) 120-pin plastic LQFP (FPT-120P-M21) 18.00±0.20(.709±.008)SQ * +0.40 +.016 SQ 16.00 .630 –0.10 –.004 90 91 INDEX 120 LEAD No. 1 0.22±0.05 0.50(.020) (.009±.002) 2002-2010 FUJITSU SEMICONDUCTOR LIMITED F120033S-c-4-7 C Please check the latest package dimension ...

Page 96

MB9B100 Series (Continued) 112-ball plastic PFBGA (BGA-112P-M04) 112-ball plastic PFBGA (BGA-112P-M04) 10.00±0.10(.394±.004) 10.00±0.10 (.394±.004) (INDEX AREA) 0.20(.008 (.014±.004) 0.10(.004) S 2003-2010 FUJITSU SEMICONDUCTOR LIMITED B112004S-c-2-3 C Please check the latest package dimension at the following URL. http://edevice.fujitsu.com/package/en-search/ 96 ...

Page 97

MAJOR CHANGES IN THIS EDITION Page Section - All 64 ELECTRICAL CHARACTERISTICS AC Characteristics (3) Built-in CR Oscillation Characteristics 85 12bit A/D Converter 90, 91 EXAMPLE OF CHARACTERISTIC 92 ORDERING INFORMATION In the previous revision, the number at the ...

Page 98

MB9B100 Series MB9B100 Series 98 98 DS706-00007-1v0-E ...

Page 99

DS706-00007-1v0-E MB9B100 Series MB9B100 Series 99 99 ...

Page 100

FUJITSU SEMICONDUCTOR LIMITED Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome, Kohoku-ku Yokohama Kanagawa 222-0033, Japan Tel: +81-45-415-5858 http://jp.fujitsu.com/fsl/en/ For further information please contact: North and South America FUJITSU SEMICONDUCTOR AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, ...

Related keywords