CSTCE8M00G55Z-R0 Murata, CSTCE8M00G55Z-R0 Datasheet - Page 43

• Manufacturer Part Number: CSTCE8M00G55Z-R0
• Description: Resonators CSTCE8M00G55Z-R0
• Manufacturer: Murata
• Series: CSTCEr

Specifications of CSTCE8M00G55Z-R0

• Tolerance: 0.5 %
• Termination Style: SMD/SMT
• Dimensions: 1.1 mm W x 3 mm L x 0.7 mm H
• Frequency: 8 MHz
• Frequency Tolerance: ± 0.5%
• Resonant Impedance: 40ohm
• Oscillator Mounting: SMD
• No. Of Pins: 3
• Operating Temperature Range: -40°C To +125°C
• Resonant Frequency: 8MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
CSBLA_E
1. Soldering Conditions
CSBLA_J
(1) Cleaning Solvents
CSBFB_J/CSBLA_J
1. Product Storage Condition
2. Expire Date on Storage
(2) Temperature Difference: dT *1
(3) Conditions
(1) Reflow
(2) Soldering Iron
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Notice (Soldering and Mounting)
Notice (Soldering and Mounting)
Notice (Storage and Operating Condition)
Please confirm solderability and characteristics
for the products regularly.
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
HCFC, Isopropanol, Tap water, Demineralized water,
dT<=30 C. (dT=Component-solvent)
1. Ultrasonic Wash
2. Immersion Wash
(a) Lead terminals are immersed up to 1.5 mm from
Cleanthrough750H, Pine alpha 100S, Techno care
FRW.
*1 ex. In case the component at +90 degrees C. immerses
The component cannot withstand reflow soldering.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 minute max. in above solvent at +60 degrees C. max.
(Frequency: 28kHz, Output: 20W/L)
5 minutes max. in above solvent at +60 degrees C. max.
components body in soldering bath of +260+-5
degrees C for 10+-1.0 seconds, and then
components shall be left in natural condition
for 1 hour.
into cleaning solvent at +60 degrees C., then
dT=30 degrees C.
2. Wash
(4) Drying
(5) Others
3. Notice on Product Storage
(3) Please do not apply excessive mechanical stress to
(1) Please do not store the products in a chemical
(2) Please do not put the products directly on the
(3) Please do not store the products in the places
(4) Please use the products immediately after the
(5) Please do not drop the products to avoid cracking
The component cannot withstand washing.
3. Shower or Rinse Wash
5 minutes max. by air blow at +80 degrees C. max.
1. Total washing time should be within 10 minutes.
2. Please insure the component is thoroughly
3. The component may be damaged if it is washed
4. Please do not apply excess mechanical stress to
5. Ultrasonic cleaning of the component is acceptable.
(b) Lead terminal is directly contacted with the tip
the component and lead terminals during soldering.
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
floor without anything under them to avoid damp
places and/or dusty places.
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
of ceramic element.
5 minutes max. in above solvent at +60 degrees C. max.
evaluated in your application circuit.
with alkali cleaning solvent.
the component and lead terminals during soldering.
However, the size of bath, size and thickness of
PBC should be evaluated to confirm stable electrical
characteristics are maintained.
of soldering iron of +350+-5 degrees C
for 3.0+-0.5 seconds, and then components shall
be left in natural condition for 1 hour.
kHz Type Notice for General Usage
Continued on the following page.
41
P16E.pdf
08.3.3
7