CSTCW48M0X51-R0 Murata, CSTCW48M0X51-R0 Datasheet - Page 45

• Manufacturer Part Number: CSTCW48M0X51-R0
• Description: Resonators 48MHz
• Manufacturer: Murata
• Series: CSTCW-Xr

Specifications of CSTCW48M0X51-R0

• Tolerance: 0.5 %
• Termination Style: SMD/SMT
• Operating Temperature Range: - 20 C to + 80 C
• Dimensions: 2 mm W x 2.5 mm L x 1.5 mm H
• Frequency Stability: 0.2 %
• Frequency: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
CSBFB_J 430-519kHz
1. Soldering Conditions
(1) Reflow
2. Wash
(1) Cleaning Solvents
(2) Temperature Difference : dT *1
(4) Drying
3. Notice for Mounting
44
(2) Soldering Iron
(3) Conditions
(5) Others
kHz Type Notice for General Usage
Notice (Soldering and Mounting)
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +140 to +160 C for
(b) Heating conditions should be within 20 seconds at
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
dT<=60 C (dT=Component-solvent)
*1 ex. In case the component at +90 C immerses into
5 minutes max. by air blow at +80 C max.
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
(a) Please insure the component is thoroughly evaluated
(b) Please do not apply excess mechanical stress to the
Soldering iron of +270 5 C should be placed 0.5mm
above electrode of resonator. Melting solder through
soldering iron should be applied to electrode for 3 1
seconds; then, after being placed in natural conditions for
24 hours, the resonator should be measured.
(a) Ultrasonic Wash
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 minute max. in above solvent at +60 C max.
60 to 120 seconds. Ascending time up to +150 C
should be longer than 30 seconds.
+225 C min., but peak temperature should be Iower
than +235 C.
(Frequency: 28kHz, Output: 20W/L)
chlorine, petroleum, or alkali cleaning solvent.
in your application circuit.
component and lead terminals during soldering.
cleaning solvent at +60 C, then dT=30 C.
(b) Immersion Wash
(c) Shower or Rinse Wash
(c) Ultrasonic cleaning of the component is acceptable.
(c) In the case of the bulk component, dry heating
5 minutes max. in above solvent at +60 C max.
5 minutes max. in above solvent at +60 C max.
225
150
100
However, the size of bath, size and thickness of PCB
should be evaluated to confirm stable electrical
characteristics are maintained.
treatment (130 C. for 5 hours min.) is required before
reflow soldering. Then, the component should be
soldered within 48 hours after dry heating treatment.
30 sec. min.
(in air)
Pre-heating
60 to 120 sec.
Soldering Peak Temperature 235 C max.
20 sec. max. 120 sec. min.
Gradual Cooling
(in air)
P16E.pdf
06.9.7