CSTCW48M0X51-R0 Murata, CSTCW48M0X51-R0 Datasheet - Page 16

• Manufacturer Part Number: CSTCW48M0X51-R0
• Description: Resonators 48MHz
• Manufacturer: Murata
• Series: CSTCW-Xr

Specifications of CSTCW48M0X51-R0

• Tolerance: 0.5 %
• Termination Style: SMD/SMT
• Operating Temperature Range: - 20 C to + 80 C
• Dimensions: 2 mm W x 2.5 mm L x 1.5 mm H
• Frequency Stability: 0.2 %
• Frequency: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering Conditions
(1) Reflow
2. Wash
(1) Cleaning Solvents
(2) Temperature Difference : dT *1
(4) Drying
3. Notice for Mounting
(2) Soldering Iron
(3) Conditions
(5) Others
CSTCV/CSACV Series
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180 C for
(b) Heating conditions should be within 40 seconds at
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
dT<=60 C (dT=Component-solvent)
*1 ex. In case the component at +90 C immerses into
5 minutes max. by air blow at +80 C max.
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
(a) The component is recommended for use with
Soldering iron of +350 5 C should be placed 0.5mm
above electrode of resonator. Melting solder through
soldering iron should be applied to electrode for 3 1
seconds; then, after being placed in natural conditions for
24 hours, the resonator should be measured.
(a) Ultrasonic Wash
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 minute max. in above solvent at +60 C max.
60 to 120 seconds. Ascending time up to +150 C
should be longer than 30 seconds.
+230 C min., but peak temperature should be Iower
than +260 C.
(Frequency: 28kHz, Output: 20W/L)
chlorine, petroleum, or alkali cleaning solvent.
placement machines which employ optical placement
capabilities. In some cases, placement machines
which utilize mechanical positioning may apply
excessive mechanical force which might result in
damage to the ceramic resonator. Please contact
Murata before mounting this product using placement
machines which use mechanical positioning.
cleaning solvent at +60 C, then dT=30 C.
MHz Chip Type Notice (Soldering and Mounting) for Automotive
(b) Immersion Wash
(c) Shower or Rinse Wash
(b) Please insure the component is thoroughly evaluated
(c) Please do not apply excess mechanical stress to the
5 minutes max. in above solvent at +60 C max.
5 minutes max. in above solvent at +60 C max.
in your application circuit.
component and terminals during soldering.
230
180
150
30 sec.
min.
(150-180˚C)
Pre-heating
60-120 sec.
(260˚C max.)
Heating
(230˚C)
40 sec.
Peak
max.
Gradual
Cooling
120 sec.
min.
15
P16E.pdf
06.9.7
2